GEM

Open Tender for LED Batten,Metal Alloy Casting Water Tap with Aerator (V2),Copper Alloy Gate Valve For Waterworks P in SIRSA, HARYANA

Bid Publish Date

26-Feb-2026, 4:24 pm

Bid End Date

09-Mar-2026, 5:00 pm

EMD

₹20,000

Location

SIRSA , HARYANA

Progress

Issue26-Feb-2026, 4:24 pm

AwardPending

Explore all 4 tabs to view complete tender details

Quantity

687

Documents 25

GeM-Bidding-8967804.pdf

Main Document

CATALOG-Specification-1

CATALOG Specification

CATALOG-Specification-2

CATALOG Specification

CATALOG-Specification-3

CATALOG Specification

CATALOG-Specification-4

CATALOG Specification

CATALOG-Specification-5

CATALOG Specification

CATALOG-Specification-6

CATALOG Specification

CATALOG-Specification-7

CATALOG Specification

CATALOG-Specification-8

CATALOG Specification

CATALOG-Specification-9

CATALOG Specification

CATALOG-Specification-10

CATALOG Specification

CATALOG-Specification-11

CATALOG Specification

CATALOG-Specification-12

CATALOG Specification

CATALOG-Specification-13

CATALOG Specification

CATALOG-Specification-14

CATALOG Specification

CATALOG-Specification-15

CATALOG Specification

CATALOG-Specification-16

CATALOG Specification

CATALOG-Specification-17

CATALOG Specification

CATALOG-Specification-18

CATALOG Specification

CATALOG-Specification-19

CATALOG Specification

CATALOG-Specification-20

CATALOG Specification

CATALOG-Specification-21

CATALOG Specification

CATALOG-Specification-22

CATALOG Specification

Buyer uploaded ATC document

ATC

GEM General Terms and Conditions Document

GEM_GENERAL_TERMS_AND_CONDITIONS

Past Similar Tenders (Historical Results)

5 found

Self Ballasted LED Lamps (LED Bulb) (V3) Conforming to IS 16102 (Part 2) (Under BIS Scheme - II),LE

Indian Army

LEH, JAMMU & KASHMIR

Posted: 13 February 2026

Closed: 23 February 2026

GEM

Indian Army Copper Alloy Taps & Bathroom Fixtures Tender Udhamap ur Jammu & Kashmir 2026 IS Standards

Indian Army

UDHAMPUR, JAMMU & KASHMIR

Posted: 17 February 2026

Closed: 23 February 2026

GEM

Indian Army Copper Alloy Taps and Sanitary Fixtures Tender Udhamapur J&K IS 8931 IS 781 IS 774 2026

Indian Army

UDHAMPUR, JAMMU & KASHMIR

Posted: 17 February 2026

Closed: 23 February 2026

GEM

Copper alloy Taps/Stop Valves (V2) Conforming to IS 8931,Copper alloy Taps/Stop Valves (V2) Conform

Indian Army

Posted: 11 February 2026

Closed: 21 February 2026

GEM

Copper alloy Taps/Stop Valves (V2) Conforming to IS 8931,Copper alloy Taps/Stop Valves (V2) Conform

Indian Army

GORAKHPUR, UTTAR PRADESH

Posted: 10 February 2026

Closed: 20 February 2026

GEM

Technical Specifications 22 Items

Item #1 Details

View Catalog

Category	Specification	Requirement
GENERIC	LED Batten Rating (in Watts)	18.0
GENERIC	Length of LED Batten (Nominal) (in mm)	1150.0
GENERIC	Lamp Efficacy (Lumen / Watt), Minimum	100, 110 Or higher
GENERIC	Warranty for free replacement (in Years)	2, 3 Or higher
CONSTRUCTIONAL	Housing Material	Polycarbonate

Item #2 Details

View Catalog

Category	Specification	Requirement
ITEM	Tap Mounting Type	Ball tap
Material	Material	Brass
Description	Type of Faucet	Half Turn
Description	Aerator Material	Plastic
Dimension	Nominal Thread Size of Tap (mm)	15

Item #3 Details

View Catalog

Category	Specification	Requirement
Generic	Conformity to IS 778	Yes
Generic	End Connection	Screwed Ends
Generic	Nominal Size of Valves (in mm)	20 mm
Generic	Pressure Classification	Class 1 Valve : Suitable for cold working pressure up to 1.0 MPa
Generic	Gate Valve Type	Solid Wedge Type
Material & Manufacture	Bonnet Type/ Design	Screwed - in bonnet integral seats
Material & Manufacture	Material of Body	Brass (conforming to DCB 2 of IS 1264)
Material & Manufacture	Material of Bonnet/Cover Material	Brass (conforming to DCB 2 of IS 1264)
Material & Manufacture	Material of Stuffing box, disc hinge, check nut, stem nut, disc retaining nut, gland, gland nut, gland flange, body seat rings and disc or wedge facing rings (where renewable	Extruded Brass Rod (conforming to Type 1 or Type 2 (Half Hard) of IS 319)
Material & Manufacture	Material of Stem, hinge pin and plug	Extruded Brass Rod (conforming to Type 2 (Half Hard) of IS 319)
Material & Manufacture	Material of Gland Packing	Hemp and Jute (conforming to IS 5414)
Dimensions	Minimum Length of Threaded Portion at the end (in mm)	10.5 mm
Dimensions	Minimum Thickness at body ends outside of the thread for both Class 1 and Class 2 Valves (in mm)	4.1 mm
Dimensions	Minimum Width of ends for both Class 1 and Class 2 Valves (in mm)	13.0 mm
Dimensions	Minimum Diameter of Stems for Both Class 1 and Class 2 Valves (in mm)	9 mm
Dimensions	Minimum Flat to Flat Size for both Class 1 and Class 2 Valves (in mm)	32 mm
Dimensions	End to End Dimensions of Screwed End Valves (in mm)	As per Table 9 of IS 778
Dimensions	Face to Face Dimensions of Flanged Valves (in mm)	As per Table 11 of IS 778

Item #4 Details

View Catalog

Category	Specification	Requirement
Generic	Conformity to IS 778	Yes
Generic	End Connection	Screwed Ends
Generic	Nominal Size of Valves (in mm)	25 mm
Generic	Pressure Classification	Class 1 Valve : Suitable for cold working pressure up to 1.0 MPa
Generic	Gate Valve Type	Solid Wedge Type
Material & Manufacture	Bonnet Type/ Design	Screwed - in bonnet integral seats
Material & Manufacture	Material of Body	Brass (conforming to DCB 2 of IS 1264)
Material & Manufacture	Material of Bonnet/Cover Material	Brass (conforming to DCB 2 of IS 1264)
Material & Manufacture	Material of Stuffing box, disc hinge, check nut, stem nut, disc retaining nut, gland, gland nut, gland flange, body seat rings and disc or wedge facing rings (where renewable	Extruded Brass Rod (conforming to Type 1 or Type 2 (Half Hard) of IS 319)
Material & Manufacture	Material of Stem, hinge pin and plug	Extruded Brass Rod (conforming to Type 2 (Half Hard) of IS 319)
Material & Manufacture	Material of Gland Packing	Hemp and Jute (conforming to IS 5414)
Dimensions	Minimum Length of Threaded Portion at the end (in mm)	12.0 mm
Dimensions	Minimum Thickness at body ends outside of the thread for both Class 1 and Class 2 Valves (in mm)	4.6 mm
Dimensions	Minimum Width of ends for both Class 1 and Class 2 Valves (in mm)	13.0 mm
Dimensions	Minimum Diameter of Stems for Both Class 1 and Class 2 Valves (in mm)	10 mm
Dimensions	Minimum Flat to Flat Size for both Class 1 and Class 2 Valves (in mm)	39 mm
Dimensions	End to End Dimensions of Screwed End Valves (in mm)	As per Table 9 of IS 778
Dimensions	Face to Face Dimensions of Flanged Valves (in mm)	As per Table 11 of IS 778

Item #5 Details

View Catalog

Category	Specification	Requirement
Generic	Conformity to IS 778	Yes
Generic	End Connection	Screwed Ends
Generic	Nominal Size of Valves (in mm)	40 mm
Generic	Pressure Classification	Class 1 Valve : Suitable for cold working pressure up to 1.0 MPa
Generic	Gate Valve Type	Solid Wedge Type
Material & Manufacture	Bonnet Type/ Design	Screwed - in bonnet integral seats
Material & Manufacture	Material of Body	Brass (conforming to DCB 2 of IS 1264)
Material & Manufacture	Material of Bonnet/Cover Material	Brass (conforming to DCB 2 of IS 1264)
Material & Manufacture	Material of Stuffing box, disc hinge, check nut, stem nut, disc retaining nut, gland, gland nut, gland flange, body seat rings and disc or wedge facing rings (where renewable	Extruded Brass Rod (conforming to Type 1 or Type 2 (Half Hard) of IS 319)
Material & Manufacture	Material of Stem, hinge pin and plug	Extruded Brass Rod (conforming to Type 2 (Half Hard) of IS 319)
Material & Manufacture	Material of Gland Packing	Hemp and Jute (conforming to IS 5414)
Dimensions	Minimum Length of Threaded Portion at the end (in mm)	13.5 mm
Dimensions	Minimum Thickness at body ends outside of the thread for both Class 1 and Class 2 Valves (in mm)	5.0 mm
Dimensions	Minimum Width of ends for both Class 1 and Class 2 Valves (in mm)	15.0 mm
Dimensions	Minimum Diameter of Stems for Both Class 1 and Class 2 Valves (in mm)	12 mm
Dimensions	Minimum Flat to Flat Size for both Class 1 and Class 2 Valves (in mm)	55 mm
Dimensions	End to End Dimensions of Screwed End Valves (in mm)	As per Table 9 of IS 778
Dimensions	Face to Face Dimensions of Flanged Valves (in mm)	As per Table 11 of IS 778

Item #6 Details

View Catalog

Category	Specification	Requirement
Generic	Conformity to IS 778	Yes
Generic	End Connection	Screwed Ends
Generic	Nominal Size of Valves (in mm)	50 mm
Generic	Pressure Classification	Class 1 Valve : Suitable for cold working pressure up to 1.0 MPa
Generic	Gate Valve Type	Solid Wedge Type
Material & Manufacture	Bonnet Type/ Design	Screwed - in bonnet integral seats
Material & Manufacture	Material of Body	Brass (conforming to DCB 2 of IS 1264)
Material & Manufacture	Material of Bonnet/Cover Material	Brass (conforming to DCB 2 of IS 1264)
Material & Manufacture	Material of Stuffing box, disc hinge, check nut, stem nut, disc retaining nut, gland, gland nut, gland flange, body seat rings and disc or wedge facing rings (where renewable	Extruded Brass Rod (conforming to Type 1 or Type 2 (Half Hard) of IS 319)
Material & Manufacture	Material of Stem, hinge pin and plug	Extruded Brass Rod (conforming to Type 2 (Half Hard) of IS 319)
Material & Manufacture	Material of Gland Packing	Hemp and Jute (conforming to IS 5414)
Dimensions	Minimum Length of Threaded Portion at the end (in mm)	17.0 mm
Dimensions	Minimum Thickness at body ends outside of the thread for both Class 1 and Class 2 Valves (in mm)	6.0 mm
Dimensions	Minimum Width of ends for both Class 1 and Class 2 Valves (in mm)	20.0 mm
Dimensions	Minimum Diameter of Stems for Both Class 1 and Class 2 Valves (in mm)	12 mm
Dimensions	Minimum Flat to Flat Size for both Class 1 and Class 2 Valves (in mm)	68 mm
Dimensions	End to End Dimensions of Screwed End Valves (in mm)	As per Table 9 of IS 778
Dimensions	Face to Face Dimensions of Flanged Valves (in mm)	As per Table 11 of IS 778

Item #7 Details

View Catalog

Category	Specification	Requirement
Specification	Governing Specification	Conforming to IS 8931
Type	Item	Type 1 Bib tap
Type	Dimension	As per table 4 of the governing specification
Type	Nominal Size of bore of pipe to which taps and valves are fitted(in mm)	15
Material	Material of body, body components, nozzle , bonnet and back nuts	Brass rods
Material	Material of inlet tubes	Brass tubes
Material	Material of flanges	Brass rods
Material	Material of diverter and diverter components	NA
Material	Material of spindle, glands, washer plate, nuts, screw and pin	Forged brass
Material	Material of circlip, wire locks	Stainless steel
Material	Material of 'O' ring , gasket, and seat washer	Synthetic rubber
Material	Material of Knob and knob components	Cast brass
Generic	Aerating device fitted with tap	No
Generic	Flow straightening device fitted with tap	No
Warranty	Warranty (in months)	12

Item #8 Details

View Catalog

Category	Specification	Requirement
Specification	Governing Specification	Conforming to IS 8931
Type	Item	Stop valve with internal thread
Type	Dimension	As per table 5 of the governing specification
Type	Nominal Size of bore of pipe to which taps and valves are fitted(in mm)	15
Material	Material of body, body components, nozzle , bonnet and back nuts	Cast brass
Material	Material of inlet tubes	Brass tubes
Material	Material of flanges	Brass sheet
Material	Material of diverter and diverter components	NA
Material	Material of spindle, glands, washer plate, nuts, screw and pin	Forged brass
Material	Material of circlip, wire locks	Phosphor bronze sheet
Material	Material of 'O' ring , gasket, and seat washer	Synthetic rubber
Material	Material of Knob and knob components	Die cast brass
Generic	Aerating device fitted with tap	Yes
Generic	Flow straightening device fitted with tap	No
Warranty	Warranty (in months)	6

Item #9 Details

View Catalog

Category	Specification	Requirement
Specification	Governing Specification	Conforming to IS 8931
Type	Item	Stop valve with internal thread
Type	Dimension	As per table 5 of the governing specification
Type	Nominal Size of bore of pipe to which taps and valves are fitted(in mm)	15
Material	Material of body, body components, nozzle , bonnet and back nuts	Brass rods
Material	Material of inlet tubes	Brass tubes
Material	Material of flanges	Brass sheet
Material	Material of diverter and diverter components	NA
Material	Material of spindle, glands, washer plate, nuts, screw and pin	Forged brass
Material	Material of circlip, wire locks	Phosphor bronze sheet
Material	Material of 'O' ring , gasket, and seat washer	Synthetic rubber
Material	Material of Knob and knob components	Cast brass
Generic	Aerating device fitted with tap	Yes
Generic	Flow straightening device fitted with tap	No
Warranty	Warranty (in months)	6

Item #10 Details

View Catalog

Category	Specification	Requirement
Specification	Governing Specification	Conforming to IS 8931
Type	Item	Stop valve with internal thread
Type	Dimension	As per table 5 of the governing specification
Type	Nominal Size of bore of pipe to which taps and valves are fitted(in mm)	15
Material	Material of body, body components, nozzle , bonnet and back nuts	Cast brass
Material	Material of inlet tubes	Brass tubes
Material	Material of flanges	Stainless steel sheet
Material	Material of diverter and diverter components	NA
Material	Material of spindle, glands, washer plate, nuts, screw and pin	Extruded brass rods
Material	Material of circlip, wire locks	Phosphor bronze sheet
Material	Material of 'O' ring , gasket, and seat washer	Synthetic rubber
Material	Material of Knob and knob components	Cast brass
Generic	Aerating device fitted with tap	Yes
Generic	Flow straightening device fitted with tap	Yes
Warranty	Warranty (in months)	12

Item #11 Details

View Catalog

Category	Specification	Requirement
Specification	Governing Specification	Conforming to IS 8931
Type	Item	Type 1 Bib tap
Type	Dimension	As per table 4 of the governing specification
Type	Nominal Size of bore of pipe to which taps and valves are fitted(in mm)	15
Material	Material of body, body components, nozzle , bonnet and back nuts	Cast brass
Material	Material of inlet tubes	Copper tubes
Material	Material of flanges	Cast brass
Material	Material of diverter and diverter components	NA
Material	Material of spindle, glands, washer plate, nuts, screw and pin	Forged brass
Material	Material of circlip, wire locks	Phosphor bronze sheet
Material	Material of 'O' ring , gasket, and seat washer	Synthetic rubber
Material	Material of Knob and knob components	Cast brass
Generic	Aerating device fitted with tap	Yes
Generic	Flow straightening device fitted with tap	Yes
Warranty	Warranty (in months)	6

Item #12 Details

View Catalog

Category	Specification	Requirement
Specification	Governing Specification	Conforming to IS 8931
Type	Item	Pillar tap
Type	Dimension	As per table 3 of the governing specification
Type	Nominal Size of bore of pipe to which taps and valves are fitted(in mm)	15
Material	Material of body, body components, nozzle , bonnet and back nuts	Die cast brass
Material	Material of inlet tubes	Brass tubes
Material	Material of flanges	Die cast brass
Material	Material of diverter and diverter components	NA
Material	Material of spindle, glands, washer plate, nuts, screw and pin	Rolled brass rods
Material	Material of circlip, wire locks	Stainless steel
Material	Material of 'O' ring , gasket, and seat washer	Neoprene rubber
Material	Material of Knob and knob components	Zinc base alloys
Generic	Aerating device fitted with tap	Yes
Generic	Flow straightening device fitted with tap	Yes
Warranty	Warranty (in months)	36

Item #13 Details

View Catalog

Category	Specification	Requirement
Type	Type of shower	Hand Shower
Type	Material of body/face plate	ABS
Type	Finish of face plate	Chrome plated
Type	Type of Water Flow	Rainfall and Multiple flow
Type	Type of Multiple flow	Massage, Cascade, Mist, Whirl, Monorail, Rainflow, Rainstream
Type	Shape of Shower	Round
Dimensions	Size of Shower	100 mm
Dimensions	Overall length of Hand Shower (in mm)	200
Dimensions	Length of Hand Shower Tube (in mt)	1.5
Dimensions	Diameter of Hand Shower Tube (in mm)	12
Dimensions	Material of Hand Shower Tube	Stainless Steel
Dimensions	Overall length of Shower Arm (in mm)	NA
Warranty	Warranty (in Years)	1

Item #14 Details

View Catalog

Category	Specification	Requirement
Generic	Pressure rating (Bar)	0.75
Generic	Flow Rate , Minimum (lpm)	8, 9, 10, 11 Or higher
Material & Construction	Material of construction	ABS
Material & Construction	Hose Material	PVC
Material & Construction	Hose length ( in meters)	1.2
Material & Construction	Handle Type	Lever
Material & Construction	Anti bacterial coating	No

Item #15 Details

View Catalog

Category	Specification	Requirement
Specification	Governing Specification	Conforming to IS 8931
Type	Item	Concealed stop valve
Type	Dimension	As per table 5 of the governing specification
Type	Nominal Size of bore of pipe to which taps and valves are fitted(in mm)	15
Material	Material of body, body components, nozzle , bonnet and back nuts	Die cast brass
Material	Material of inlet tubes	Copper tubes
Material	Material of flanges	Brass rods
Material	Material of diverter and diverter components	NA
Material	Material of spindle, glands, washer plate, nuts, screw and pin	Forged brass
Material	Material of circlip, wire locks	Stainless steel
Material	Material of 'O' ring , gasket, and seat washer	Neoprene rubber
Material	Material of Knob and knob components	Die cast brass
Generic	Aerating device fitted with tap	No
Generic	Flow straightening device fitted with tap	No
Warranty	Warranty (in months)	6

Item #16 Details

View Catalog

Category	Specification	Requirement
Specification	Governing Specification	Conforming to IS 8931
Type	Item	Pillar tap
Type	Dimension	As per table 3 of the governing specification
Type	Nominal Size of bore of pipe to which taps and valves are fitted(in mm)	15
Material	Material of body, body components, nozzle , bonnet and back nuts	Cast brass
Material	Material of inlet tubes	Brass tubes
Material	Material of flanges	Stainless steel sheet
Material	Material of diverter and diverter components	NA
Material	Material of spindle, glands, washer plate, nuts, screw and pin	Extruded brass rods
Material	Material of circlip, wire locks	Phosphor bronze sheet
Material	Material of 'O' ring , gasket, and seat washer	Synthetic rubber
Material	Material of Knob and knob components	Zinc base alloys
Generic	Aerating device fitted with tap	Yes
Generic	Flow straightening device fitted with tap	Yes
Warranty	Warranty (in months)	12

Item #17 Details

View Catalog

Category	Specification	Requirement
GENERIC	LED Batten Rating (in Watts)	10.0
GENERIC	Length of LED Batten (Nominal) (in mm)	560.0
GENERIC	Lamp Efficacy (Lumen / Watt), Minimum	100, 110 Or higher
GENERIC	Warranty for free replacement (in Years)	1, 2, 3 Or higher
CONSTRUCTIONAL	Housing Material	Polycarbonate

Item #18 Details

View Catalog

Category	Specification	Requirement
Specification	Governing Specification	Conforming to IS 8931
Type	Item	Stop valve with internal thread
Type	Dimension	As per table 5 of the governing specification
Type	Nominal Size of bore of pipe to which taps and valves are fitted(in mm)	15
Material	Material of body, body components, nozzle , bonnet and back nuts	Cast brass
Material	Material of inlet tubes	Brass tubes
Material	Material of flanges	Forged brass
Material	Material of diverter and diverter components	NA
Material	Material of spindle, glands, washer plate, nuts, screw and pin	Forged brass
Material	Material of circlip, wire locks	Stainless steel
Material	Material of 'O' ring , gasket, and seat washer	Synthetic rubber
Material	Material of Knob and knob components	Zinc base alloys
Generic	Aerating device fitted with tap	No
Generic	Flow straightening device fitted with tap	No
Warranty	Warranty (in months)	6

Item #19 Details

View Catalog

Category	Specification	Requirement
GENERIC	Configuration	With 3-Shelf (including top shelf)
GENERIC	Shape of support structure	Rectangular hollow type
GENERIC	Ground clearance (mm)	25 mm
GENERIC	Mode of supply	Knocked Down To Be Assembled At Consignee Site By Consignee Himself
MATERIAL & MATERIAL THICKNESS	Shelf material	Stainless Steel Grade 202 galvanized
MATERIAL & MATERIAL THICKNESS	Shelf material thickness	0.6 mm
MATERIAL & MATERIAL THICKNESS	Support structure material	Stainless Steel Grade 202 galvanized
MATERIAL & MATERIAL THICKNESS	Support structure material thickness	0.6 mm
DIMENSION	Width of shelf rack ± 10 mm	915 mm
DIMENSION	Depth of shelf rack ± 10 mm	405 mm
DIMENSION	Height of shelf rack ± 10 mm	1220 mm
DIMENSION	Height of support structure ± 10 mm	1245 mm
DIMENSION	Size of support structure	30 mm x 30 mm
WARRANTY	Warranty period	1 - Year
CERTIFICATION	Test report to be furnished to buyer on demand	No

Item #20 Details

View Catalog

Category	Specification	Requirement
Generic	Conformity to IS 9763	Yes
Generic	Product Type	Plastic Bib Tap
Generic	Nominal Size (in mm)	15 mm (1/2")
Generic	Hot/Cold Identification of Control Devices	Blue Color or Letter C for Cold Water
Materials	Material of Body of Tap/ Valve	PP Copolymer (conforming to IS 10910)
Materials	Material of Bonnet of Tap/ Valve	PBT (conforming to IS 13193)
Materials	Material of Spindle of Tap/ Valve	PP Copolymer (conforming to IS 10910)
Materials	Material of Handle of Tap/ Valve	PBT (conforming to IS 13193)
Materials	Material of Seal of Tap/ Valve	Rubber
Dimensions & Construction	Dimensions (in mm)	Bib Taps (As per Table 3 of IS 9763)

Item #21 Details

View Catalog

Category	Specification	Requirement
Generic	Conformity to IS 9763	Yes
Generic	Product Type	Stop Valve
Generic	Nominal Size (in mm)	15 mm (1/2")
Generic	Hot/Cold Identification of Control Devices	Blue Color or Letter C for Cold Water
Materials	Material of Body of Tap/ Valve	PP Copolymer (conforming to IS 10910)
Materials	Material of Bonnet of Tap/ Valve	PP Copolymer (conforming to IS 10910)
Materials	Material of Spindle of Tap/ Valve	PBT (conforming to IS 13193)
Materials	Material of Handle of Tap/ Valve	PP Copolymer (conforming to IS 10910)
Materials	Material of Seal of Tap/ Valve	Rubber
Dimensions & Construction	Dimensions (in mm)	Stop Valves (As per Table 5 of IS 9763)

Item #22 Details

View Catalog

Category	Specification	Requirement
Generic	Conformity to IS 9763	Yes
Generic	Product Type	Angle Valve
Generic	Nominal Size (in mm)	15 mm (1/2")
Generic	Hot/Cold Identification of Control Devices	Blue Color or Letter C for Cold Water
Materials	Material of Body of Tap/ Valve	PP Copolymer (conforming to IS 10910)
Materials	Material of Bonnet of Tap/ Valve	PP Copolymer (conforming to IS 10910)
Materials	Material of Spindle of Tap/ Valve	PP Copolymer (conforming to IS 10910)
Materials	Material of Handle of Tap/ Valve	PP Copolymer (conforming to IS 10910)
Materials	Material of Seal of Tap/ Valve	Rubber
Dimensions & Construction	Dimensions (in mm)	Angle Valves (As per Table 6 of IS 9763)

🤖 AI-Powered Bidder Prediction

Discover companies most likely to bid on this tender

Live AI

Historical Data

Required Documents

Experience Criteria

Past Performance

Bidder Turnover

Certificate (Requested in ATC)

OEM Authorization Certificate

Additional Doc 1 (Requested in ATC)

Compliance of BoQ specification and supporting document *In case any bidder is seeking exemption from Experience / Turnover Criteria

the supporting documents to prove his eligibility for exemption must be uploaded for evaluation by the buyer

Similar Tenders

5 found

Tower Bolts (Non-Ferrous Metals) V2 as per IS 204,Copper alloy Taps/Stop Valves (V2) Conforming to

Indian Army

EMD: ₹91,058

Est: ₹30.4 L

⏰ Deadline: 3 weeks left

🛒 Type: Goods

View GEM

Metal Alloy Casting Water Tap with Aerator (V2)

N/a

⏰ Deadline: 2 weeks left

🛒 Type: Goods

View GEM

Copper alloy Taps/Stop Valves (V2) Conforming to IS 8931,Copper alloy Taps/Stop Valves (V2) Conform

Indian Army

📍 WEST DELHI, DELHI

EMD: ₹42,000

⏰ Deadline: 2 weeks left

🛒 Type: Goods

View GEM

Bathroom or Toilet Mirror (V3),Towel Ring,Towel Rail,Towel Rail,Copper Alloy Gate Valve For Waterwo

Indian Army

📍 WEST DELHI, DELHI

EMD: ₹66,000

⏰ Deadline: 2 weeks left

🛒 Type: Goods

View GEM

Copper Alloy Gate Valve For Waterworks Purpose (V2) Conforming to IS 778,Copper Alloy Gate Valve Fo

Indian Army

📍 LUDHIANA, PUNJAB

EMD: ₹1.0 L

⏰ Deadline: 2 weeks left

🛒 Type: Goods

View GEM

Explore More Opportunities

Quick Access

All Tenders Browse all opportunities

HARYANA State tenders

SIRSA , HARYANA City tenders

Categories 4 available

FLUID MECHANICS EQUIPMENT

SLIDER VALVES

DISCRETE COMPONENTS

AD FILM

Unlock Tender Documents

Performance Analytics

7-metric analysis with year-wise breakdown

Competitor Intelligence

Multi-dimensional analysis across 6 parameters

Market Penetration

By department, ministry, geography & category

Historical Analysis

Complete tender history with results

Documents 25

GeM-Bidding-8967804.pdf

Main Document

CATALOG-Specification-1

CATALOG Specification

CATALOG-Specification-2

CATALOG Specification

CATALOG-Specification-3

CATALOG Specification

CATALOG-Specification-4

CATALOG Specification

CATALOG-Specification-5

CATALOG Specification

CATALOG-Specification-6

CATALOG Specification

CATALOG-Specification-7

CATALOG Specification

CATALOG-Specification-8

CATALOG Specification

CATALOG-Specification-9

CATALOG Specification

CATALOG-Specification-10

CATALOG Specification

CATALOG-Specification-11

CATALOG Specification

CATALOG-Specification-12

CATALOG Specification

CATALOG-Specification-13

CATALOG Specification

CATALOG-Specification-14

CATALOG Specification

CATALOG-Specification-15

CATALOG Specification

CATALOG-Specification-16

CATALOG Specification

CATALOG-Specification-17

CATALOG Specification

CATALOG-Specification-18

CATALOG Specification

CATALOG-Specification-19

CATALOG Specification

CATALOG-Specification-20

CATALOG Specification

CATALOG-Specification-21

CATALOG Specification

CATALOG-Specification-22

CATALOG Specification

Buyer uploaded ATC document

ATC

GEM General Terms and Conditions Document

GEM_GENERAL_TERMS_AND_CONDITIONS

Browse Tenders

Categories

States

Cities

Authorities

Open Tender for LED Batten,Metal Alloy Casting Water Tap with Aerator (V2),Copper Alloy Gate Valve For Waterworks P in SIRSA, HARYANA

Categories 30

Documents 25

GeM-Bidding-8967804.pdf

CATALOG-Specification-1

CATALOG-Specification-2

CATALOG-Specification-3

CATALOG-Specification-4

CATALOG-Specification-5

CATALOG-Specification-6

CATALOG-Specification-7

CATALOG-Specification-8

CATALOG-Specification-9

CATALOG-Specification-10

CATALOG-Specification-11

CATALOG-Specification-12

CATALOG-Specification-13

CATALOG-Specification-14

CATALOG-Specification-15

CATALOG-Specification-16

CATALOG-Specification-17

CATALOG-Specification-18

CATALOG-Specification-19

CATALOG-Specification-20

CATALOG-Specification-21

CATALOG-Specification-22

Buyer uploaded ATC document

GEM General Terms and Conditions Document

Past Similar Tenders (Historical Results)

Self Ballasted LED Lamps (LED Bulb) (V3) Conforming to IS 16102 (Part 2) (Under BIS Scheme - II),LE

Indian Army Copper Alloy Taps & Bathroom Fixtures Tender Udhamap ur Jammu & Kashmir 2026 IS Standards

Indian Army Copper Alloy Taps and Sanitary Fixtures Tender Udhamapur J&K IS 8931 IS 781 IS 774 2026

Copper alloy Taps/Stop Valves (V2) Conforming to IS 8931,Copper alloy Taps/Stop Valves (V2) Conform

Copper alloy Taps/Stop Valves (V2) Conforming to IS 8931,Copper alloy Taps/Stop Valves (V2) Conform

Technical Specifications 22 Items

Item #1 Details

Item #2 Details

Item #3 Details

Item #4 Details

Item #5 Details

Item #6 Details

Item #7 Details

Item #8 Details

Item #9 Details

Item #10 Details

Item #11 Details

Item #12 Details

Item #13 Details

Item #14 Details

Item #15 Details

Item #16 Details

Item #17 Details

Item #18 Details

Item #19 Details

Item #20 Details

Item #21 Details

Item #22 Details

🤖 AI-Powered Bidder Prediction

Required Documents

Similar Tenders

Tower Bolts (Non-Ferrous Metals) V2 as per IS 204,Copper alloy Taps/Stop Valves (V2) Conforming to

Metal Alloy Casting Water Tap with Aerator (V2)

Copper alloy Taps/Stop Valves (V2) Conforming to IS 8931,Copper alloy Taps/Stop Valves (V2) Conform

Bathroom or Toilet Mirror (V3),Towel Ring,Towel Rail,Towel Rail,Copper Alloy Gate Valve For Waterwo

Copper Alloy Gate Valve For Waterworks Purpose (V2) Conforming to IS 778,Copper Alloy Gate Valve Fo

Explore More Opportunities

Unlock Tender Documents

Documents 25

GeM-Bidding-8967804.pdf

CATALOG-Specification-1

CATALOG-Specification-2

CATALOG-Specification-3

CATALOG-Specification-4

CATALOG-Specification-5

CATALOG-Specification-6