Open Tender for Design, drawing, fabrication supply erection, testing and commissioning of U/S gate of fixed wheel vertical lift type (5550mm x 3750 mm) including embedded parts and concreting including all cost of materials, machinery labour, cutting, aligning, welding, finishing, cleaning, applying, one cost of zinc rich eposy primer and three coats of cold applied epoxy paint complete job as per specification & direction of E/I. in BIHAR
Bid Publish Date
09-Dec-2021, 11:51 am
Bid End Date
22-Dec-2021, 3:00 pm
EMD
₹4,94,000
Value
₹0
Location
Progress
Tender Type
Open
Tender Fee
₹10,000
Tender Fee Exemption
No
EMD Exemption
No
Category
ITMRATE
Categories
50
The issuing authority invites bids for Design, drawing, Fabrication, supply, erection, fitting, fixing & testing commissioning of under Sluice gate and head Regulator gate, hoisting bridge hoisting system and automated gate for kao weir irrigation scheme at Wazirganj, Sasaram in Rohtas district. . (GROUP-01) in BIHAR. Submission Deadline: 22-12-2021 15: 00: 00. Submit your proposal before the deadline.
Additional Tender Data
Commercial Details
Processing Fee
₹590
Tender Currency
INR
Bid Currency
INR
Ranking Sequence
L1 Ranking
Estimated Value Visibility
N
Bid To RA
No
Authority & Contact
Organization Hierarchy
Government of Bihar->Water Resources Department->C.E. ( MECH.) PATNA->IRRIGATION MECHANICAL CIRCLE, GAYA, CAMP-DEHRI
Approving Authority
ASHOK KUMAR YADAV (SE)
Tender Creator
Mr SATYENDRA SINGH (SUPERINTENDENT ENGINEER)
Pre-Bid & Qualification
Pre-Bid Meeting Start
13-12-2021 15:00:00
Pre-Bid Meeting End
13-12-2021 16:00:00
Pre-Bid Discussion Type
OFFLINE
Pre-Bid Venue
REFER NIT FOR THE SAME.
Payment Breakdown
| Type | Amount | Currency | Mode | Exemption |
|---|---|---|---|---|
| EMD | ₹4,94,000 | INR | Internet Payment Gateway(IPG),Challan|Bank Guarantee | No |
| Tender Fee | ₹10,000 | INR | Internet Payment Gateway(IPG),Challan| | No |
| Tender Processing Fee | ₹590 | INR | Internet Payment Gateway(IPG),Challan| | No |
Document Requirements
(i) Legal Status of Bidder.
(ii) Place of Registration.
(iii) Principal place of Business
(iv) Power of attorney of signatory Bid
Total value of Mechanical engineering works performed in last five years 2016-17
Total value of Mechanical engineering works performed in last five years 2017-18
Total value of Mechanical engineering works performed in last five years 2018-19
Total value of Mechanical engineering works performed in last five years 2019-20
Total value of Mechanical engineering works performed in last five years 2020-21
Work Experience of Similar nature
Minimum Quantities of work done as prime contractor in any one year during last five years.
Bidding Capacity:
(a) Existing commitments and ongoing works
(b) Work for which Bid already submitted
Availability of key items of Contractor's Equipment
Key Personnel
Evidence of accesses to Financial Resources
Proposed methodology and programme of work
Litigation History
Affidavit
Undertaking
Time of Completion
CHARACTER certificate
Registration No.
I.T. & G. S.T. Registration & clearance Certificate
NOC for Debar (If required)
Additional document as per mentioned NIQ and Tender document if requireD.
Bid Security (Earnest Money Deposite)
General Particulars
Bid Security (Earnest Money Deposite)
(i) Legal Status of Bidder.
(ii) Place of Registration.
(iv) Power of attorney of signatory Bid
Total value of Mechanical engineering works performed in last five years 2016-17.
Total value of Mechanical engineering works performed in last five years 2017-18.
Total value of Mechanical engineering works performed in last five years 2018-19.
Total value of Mechanical engineering works performed in last five years 2019-20.
Total value of Mechanical engineering works performed in last five years 2020-21.
Work Experience of Similar nature
Minimum Quantities of work done as prime contractor in any one year during last five years.
Bidding Capacity: More than the total Bid value of present work = A*N*3-B=Rs. ____.Where A = Maxm. Value of work executed in any one yr during last 5 yrs. N= Nos of years for completion of works. B=Value of existing commitments & ongoing works to be completed in period (Rs. in lakh)
(a) Existing commitments and ongoing works
(b) Work for which Bid already submitted
Availability of key items of Contractor's Equipment
Key Personnel (Personnel/Qualification/Contract Package Size)
Evidence of accesses to Financial Resources. Evidence of access to or availability of creadit facilities (10% of estimated cost), certified by bankers (Not more than 3 months old). (Rs in Lakhs).
Proposed methodology and programme of work. Justifying their capability of execution and completion of the work as per technical specifications within the stipulated period of completion as per milestones. (Attached or not).
Litigation History. Information regarding any litigation, current or during the last five years, in which the Bidder is involved, the parties concerned, and disputed amount. (Attached or not).
Affidavit. Regarding statements made in the required attachments are true and correct.
Undertaking. Able to invest a minimum of cost upto 25% of contract value of work. During implementation of contract.
Time of Completion
CHARACTER certificate
Registration No.
I.T. & G. S.T. Registration & clearance Certificate
NOC for Debar (If required)
Tender Terms
Section 1
1. NIQ KAO WEIR.docxDetailsAccepted all terms and conditions as per mentioned NIQ and Tender Document.
Section 1
1. NIQ KAO WEIR.docxDetailsAccepted all terms and conditions as per mentioned NIQ and Tender Document.
Accepted all terms and conditions as per mentioned NIQ and Tender Document.
Section 2
2. SBD KAO WEIR.docDetailsAccepted all terms and conditions as per mentioned SBD Document.
Section 2
2. SBD KAO WEIR.docDetailsAccepted all terms and conditions as per mentioned SBD Document.
Accepted all terms and conditions as per mentioned SBD Document.
Authority Records
BID & GeM Expert Consultancy
End-to-end support — bid preparation, GeM registration, document filing & compliance by industry experts.
Free consultation · 24h response
Documents 7
1. NIQ KAO WEIR.docx
GENERAL_DOCUMENT
2. SBD KAO WEIR.doc
GENERAL_DOCUMENT
1 NIQ 03-2021-22 KAO WEIR.docx
GENERAL_DOCUMENT
2 SBD NIQ 03-2021-22 KAO WEIR.doc
GENERAL_DOCUMENT
3 TECHNICAL SHEET NIQ 03-2021-22 KAO WEIR.xls
GENERAL_DOCUMENT
VIEW ONLY BOQ N.I.Q. 03-2021-22.xlsx
BOQ
Corrigendum Lt. No. 1003, 11-12-2021.pdf
CORRIGENDUM
Bill of Quantities (BOQ)
20 Items Sign in to view GEM price trends Sign in for GEM prices
Design, drawing, fabrication supply erection, testing and commissioning of U/S gate of fixed wheel vertical lift type (5550mm x 3750 mm) including embedded parts and concreting including all cost of materials, machinery labour, cutting, aligning, welding, finishing, cleaning, applying, one cost of zinc rich eposy primer and three coats of cold applied epoxy paint complete job as per specification & direction of E/I.
Design, drawing, fabrication supply erection, testing and commissioning of U/S gate of fixed wheel vertical lift type (5550mm x 3750 mm) including embedded parts and concreting including all cost of materials, machinery labour, cutting, aligning, welding, finishing, cleaning, applying, one cost of zinc rich eposy primer and three coats of cold applied epoxy paint complete job as per specification & direction of E/I.
Design, drawing of structural steel hoist bridge consisting of main beams, cross beams, stiffners, chequered plates, Covering hand railing. With all other accessories for supporting rope drum and reduction unit hoisting system for operating U/S gates with cost of all materials and labour all complete job and cleaning hand applying zinc red oxide primer and three coats of synthetic enamel paints etc. as specification & direction of E/I.
Design, drawing of structural steel hoist bridge consisting of main beams, cross beams, stiffners, chequered plates, Covering hand railing. With all other accessories for supporting rope drum and reduction unit hoisting system for operating U/S gates with cost of all materials and labour all complete job and cleaning hand applying zinc red oxide primer and three coats of synthetic enamel paints etc. as specification & direction of E/I.
Design, drawing commissioning of adequate capacity double rope drum reduction unit of standard make / reduction / Shanti gear connecting nut bolts, lubricating oil etc. with all accessories including cost of materials, machinery labour charges cutting, aligning, anchoring, welding, finishing, cleaning, applying two coats of zinc red oxide primer and three coats of synthetic enamel paints etc. as specification & direction of E/I.
Design, drawing commissioning of adequate capacity double rope drum reduction unit of standard make / reduction / Shanti gear connecting nut bolts, lubricating oil etc. with all accessories including cost of materials, machinery labour charges cutting, aligning, anchoring, welding, finishing, cleaning, applying two coats of zinc red oxide primer and three coats of synthetic enamel paints etc. as specification & direction of E/I.
Fabrication erection of 04 Nos. H/R gate made by 8 mm thick skin plate with framing 75x75x10mm Vertical stiffener and Horizontal stiffener ISA 75x75x10mm, side channel ismc 100 ,bottom sill beam ISMB 100, side channel and bottom sill beam anchoring with 16 mm dia MS Rod with railing including cost of all materials labour taxes etc as per specification and direction of E/I.
Fabrication erection of 04 Nos. H/R gate made by 8 mm thick skin plate with framing 75x75x10mm Vertical stiffener and Horizontal stiffener ISA 75x75x10mm, side channel ismc 100 ,bottom sill beam ISMB 100, side channel and bottom sill beam anchoring with 16 mm dia MS Rod with railing including cost of all materials labour taxes etc as per specification and direction of E/I.
Supply fitting fixing 63 mm dia checknut with internal G.M Bush threading for matching same dia spindle fitted steel balls/thurst bearing base plate operating handle etc with cost of all materials labour taxes etc as per specification and direction of E/I..
Supply fitting fixing 63 mm dia checknut with internal G.M Bush threading for matching same dia spindle fitted steel balls/thurst bearing base plate operating handle etc with cost of all materials labour taxes etc as per specification and direction of E/I..
Supply fitting fixing 63 mm dia spindle with double start 2 TPI threaded for matching same dia checknut including cost of all materials labour taxes etc as per specification and direction of E/I.
Supply fitting fixing 63 mm dia spindle with double start 2 TPI threaded for matching same dia checknut including cost of all materials labour taxes etc as per specification and direction of E/I.
"Supply fitting fixing and installation of stairs on platform having ISMB 200 long and pedestal 22 nos. attached with stairs. Both side of U/S gate. "
"Supply fitting fixing and installation of stairs on platform having ISMB 200 long and pedestal 22 nos. attached with stairs. Both side of U/S gate. "
Design ,Fabrication , Supply , Transportation at Site of Gate leaf with Portal frame including embedded parts for 7 Nos. of 3.7 m x 1.2 m size automatic gates including fulcrum assemblies, gate leaf, end girders, hoisting brackets,steel track plates ,bronze bush ,stainless steel axles and nut ,bolts,rubber seal etc complete including cost of all materials with all leads and lifts and as directed by Engineer-in-charge of work.
Design ,Fabrication , Supply , Transportation at Site of Gate leaf with Portal frame including embedded parts for 7 Nos. of 3.7 m x 1.2 m size automatic gates including fulcrum assemblies, gate leaf, end girders, hoisting brackets,steel track plates ,bronze bush ,stainless steel axles and nut ,bolts,rubber seal etc complete including cost of all materials with all leads and lifts and as directed by Engineer-in-charge of work.
Erection ,Testing and Commissioning of Gate leaf with Portal frame including embedde parts for 7 Nos. of 3.7 m x 1.2 m size automatic gates including fulcrum assemblies, gate leaf, end girders, hoisting brackets,steel track plates ,bronze bush ,stainless steel axles and nut ,bolts ,rubber seal etc complete including cost of all materials with all leads and lifts and as directed by Engineer-in-charge of work.
Erection ,Testing and Commissioning of Gate leaf with Portal frame including embedde parts for 7 Nos. of 3.7 m x 1.2 m size automatic gates including fulcrum assemblies, gate leaf, end girders, hoisting brackets,steel track plates ,bronze bush ,stainless steel axles and nut ,bolts ,rubber seal etc complete including cost of all materials with all leads and lifts and as directed by Engineer-in-charge of work.
Design, Fabrication, Supply, transportation at site of Steel Service Bridge with GI pipe railing for of 3.7m x 1.2m size automatic gates Including cost of all materials, etc. complete as directed by Engineer-in-charge.
Design, Fabrication, Supply, transportation at site of Steel Service Bridge with GI pipe railing for of 3.7m x 1.2m size automatic gates Including cost of all materials, etc. complete as directed by Engineer-in-charge.
Erection, testing & commissioning of Steel Service Bridge with GI pipe railing for of 3.7m x 1.2m size automatic gates Including cost of all materials, etc. complete as directed by Engineer-in-charge.
Erection, testing & commissioning of Steel Service Bridge with GI pipe railing for of 3.7m x 1.2m size automatic gates Including cost of all materials, etc. complete as directed by Engineer-in-charge.
Design, Fabrication, supply, transportation at site of Low Level Friction Damper for 14 Nos. of 3.7m x 1.2m size automatic Gates including Lever Arm, Box for shoe, friction track, disc spring, damper etc. complete including cost of all materials with all leads & lifts as directed by the Engineer in Charge.
Design, Fabrication, supply, transportation at site of Low Level Friction Damper for 14 Nos. of 3.7m x 1.2m size automatic Gates including Lever Arm, Box for shoe, friction track, disc spring, damper etc. complete including cost of all materials with all leads & lifts as directed by the Engineer in Charge.
Erection, testing & commissioning of Low Level Friction Damper for 14 Nos. of 3.7m x 1.2m size automatic Gates including Lever Arm, Box for shoe, friction track, disc spring, damper etc. complete including cost of all materials with all leads & lifts as directed by the Engineer in Charge.
Erection, testing & commissioning of Low Level Friction Damper for 14 Nos. of 3.7m x 1.2m size automatic Gates including Lever Arm, Box for shoe, friction track, disc spring, damper etc. complete including cost of all materials with all leads & lifts as directed by the Engineer in Charge.
Design, Manufacture, Supply, transportation to site of 6 set of Portable Emergency Hydraulic Hoisting System for Automated Gates consisting of Hydraulic cylinder pump, hoses etc. complete including cost of all materials with all leads & lifts as directed by the Engineer in Charge.
Design, Manufacture, Supply, transportation to site of 6 set of Portable Emergency Hydraulic Hoisting System for Automated Gates consisting of Hydraulic cylinder pump, hoses etc. complete including cost of all materials with all leads & lifts as directed by the Engineer in Charge.
Erection, testing & commissioning of 6set of Portable Emergency Hydraulic Hoisting System for Automated Gates consisting of Hydraulic cylinder pump, hoses etc. complete including cost of all materials with all leads & lifts as directed by the Engineer in Charge.
Erection, testing & commissioning of 6set of Portable Emergency Hydraulic Hoisting System for Automated Gates consisting of Hydraulic cylinder pump, hoses etc. complete including cost of all materials with all leads & lifts as directed by the Engineer in Charge.
Providing Operation and Maintenance with Security of Complete System for 36 months (3 Years) round the clock including spares on Free of Cost Basis Complete job as per requirement and direction of E/I.
Providing Operation and Maintenance with Security of Complete System for 36 months (3 Years) round the clock including spares on Free of Cost Basis Complete job as per requirement and direction of E/I.
Providing Oiling ,Greasing and General Maintenance of Complete System for 36 months (3 Years).
Providing Oiling ,Greasing and General Maintenance of Complete System for 36 months (3 Years).
Provision for cost of Groove cutting/Concrete breaking in P:C:C/R:C:C by mech instrument or manually for proper anchoring of embeded bottom seal beam etc.all cost of all materials with all leads & lifts as directed by the Engineer in Charge.
Provision for cost of Groove cutting/Concrete breaking in P:C:C/R:C:C by mech instrument or manually for proper anchoring of embeded bottom seal beam etc.all cost of all materials with all leads & lifts as directed by the Engineer in Charge.
Providing and laying in Situ M20 Cement concrete in bottom and side groove of gate , including centering and shuttering from work including machine,mixing, laying,vibrating, curing with all leads and lifts, loading and unloading including the cost of all materials equipment, labour etc complete as per specifications and direction of Engineer in charge for CC 1:1.5:3 (M20).
Providing and laying in Situ M20 Cement concrete in bottom and side groove of gate , including centering and shuttering from work including machine,mixing, laying,vibrating, curing with all leads and lifts, loading and unloading including the cost of all materials equipment, labour etc complete as per specifications and direction of Engineer in charge for CC 1:1.5:3 (M20).
Drilling of holes of required size for installation of Anchor Bolts/Bars by usage of suitable template and Supply & fixing of Anchor bolts/bars accurately by usage of suitable template and using cementotious bonding material & it includes all lead & lift etc., as directed by Engineer-in-charge.
Drilling of holes of required size for installation of Anchor Bolts/Bars by usage of suitable template and Supply & fixing of Anchor bolts/bars accurately by usage of suitable template and using cementotious bonding material & it includes all lead & lift etc., as directed by Engineer-in-charge.
| Item # | Title | Description | Quantity | Unit | Consignee | Delivery (Days) | Mandatory | Price Trends |
|---|---|---|---|---|---|---|---|---|
| 1 | Design, drawing, fabrication supply erection, testing and commissioning of U/S gate of fixed wheel vertical lift type (5550mm x 3750 mm) including embedded parts and concreting including all cost of materials, machinery labour, cutting, aligning, welding, finishing, cleaning, applying, one cost of zinc rich eposy primer and three coats of cold applied epoxy paint complete job as per specification & direction of E/I. | Design, drawing, fabrication supply erection, testing and commissioning of U/S gate of fixed wheel vertical lift type (5550mm x 3750 mm) including embedded parts and concreting including all cost of materials, machinery labour, cutting, aligning, welding, finishing, cleaning, applying, one cost of zinc rich eposy primer and three coats of cold applied epoxy paint complete job as per specification & direction of E/I. | 2 | each | - | - | Yes | |
| 2 | Design, drawing of structural steel hoist bridge consisting of main beams, cross beams, stiffners, chequered plates, Covering hand railing. With all other accessories for supporting rope drum and reduction unit hoisting system for operating U/S gates with cost of all materials and labour all complete job and cleaning hand applying zinc red oxide primer and three coats of synthetic enamel paints etc. as specification & direction of E/I. | Design, drawing of structural steel hoist bridge consisting of main beams, cross beams, stiffners, chequered plates, Covering hand railing. With all other accessories for supporting rope drum and reduction unit hoisting system for operating U/S gates with cost of all materials and labour all complete job and cleaning hand applying zinc red oxide primer and three coats of synthetic enamel paints etc. as specification & direction of E/I. | 2 | each | - | - | Yes | |
| 3 | Design, drawing commissioning of adequate capacity double rope drum reduction unit of standard make / reduction / Shanti gear connecting nut bolts, lubricating oil etc. with all accessories including cost of materials, machinery labour charges cutting, aligning, anchoring, welding, finishing, cleaning, applying two coats of zinc red oxide primer and three coats of synthetic enamel paints etc. as specification & direction of E/I. | Design, drawing commissioning of adequate capacity double rope drum reduction unit of standard make / reduction / Shanti gear connecting nut bolts, lubricating oil etc. with all accessories including cost of materials, machinery labour charges cutting, aligning, anchoring, welding, finishing, cleaning, applying two coats of zinc red oxide primer and three coats of synthetic enamel paints etc. as specification & direction of E/I. | 2 | each | - | - | Yes | |
| 4 | Fabrication erection of 04 Nos. H/R gate made by 8 mm thick skin plate with framing 75x75x10mm Vertical stiffener and Horizontal stiffener ISA 75x75x10mm, side channel ismc 100 ,bottom sill beam ISMB 100, side channel and bottom sill beam anchoring with 16 mm dia MS Rod with railing including cost of all materials labour taxes etc as per specification and direction of E/I. | Fabrication erection of 04 Nos. H/R gate made by 8 mm thick skin plate with framing 75x75x10mm Vertical stiffener and Horizontal stiffener ISA 75x75x10mm, side channel ismc 100 ,bottom sill beam ISMB 100, side channel and bottom sill beam anchoring with 16 mm dia MS Rod with railing including cost of all materials labour taxes etc as per specification and direction of E/I. | 4 | each | - | - | Yes | |
| 5 | Supply fitting fixing 63 mm dia checknut with internal G.M Bush threading for matching same dia spindle fitted steel balls/thurst bearing base plate operating handle etc with cost of all materials labour taxes etc as per specification and direction of E/I.. | Supply fitting fixing 63 mm dia checknut with internal G.M Bush threading for matching same dia spindle fitted steel balls/thurst bearing base plate operating handle etc with cost of all materials labour taxes etc as per specification and direction of E/I.. | 4 | each | - | - | Yes | |
| 6 | Supply fitting fixing 63 mm dia spindle with double start 2 TPI threaded for matching same dia checknut including cost of all materials labour taxes etc as per specification and direction of E/I. | Supply fitting fixing 63 mm dia spindle with double start 2 TPI threaded for matching same dia checknut including cost of all materials labour taxes etc as per specification and direction of E/I. | 18 | Meter | - | - | Yes | |
| 7 | "Supply fitting fixing and installation of stairs on platform having ISMB 200 long and pedestal 22 nos. attached with stairs. Both side of U/S gate. " | "Supply fitting fixing and installation of stairs on platform having ISMB 200 long and pedestal 22 nos. attached with stairs. Both side of U/S gate. " | 2 | each | - | - | Yes | |
| 8 | Design ,Fabrication , Supply , Transportation at Site of Gate leaf with Portal frame including embedded parts for 7 Nos. of 3.7 m x 1.2 m size automatic gates including fulcrum assemblies, gate leaf, end girders, hoisting brackets,steel track plates ,bronze bush ,stainless steel axles and nut ,bolts,rubber seal etc complete including cost of all materials with all leads and lifts and as directed by Engineer-in-charge of work. | Design ,Fabrication , Supply , Transportation at Site of Gate leaf with Portal frame including embedded parts for 7 Nos. of 3.7 m x 1.2 m size automatic gates including fulcrum assemblies, gate leaf, end girders, hoisting brackets,steel track plates ,bronze bush ,stainless steel axles and nut ,bolts,rubber seal etc complete including cost of all materials with all leads and lifts and as directed by Engineer-in-charge of work. | 7 | No | - | - | Yes | |
| 9 | Erection ,Testing and Commissioning of Gate leaf with Portal frame including embedde parts for 7 Nos. of 3.7 m x 1.2 m size automatic gates including fulcrum assemblies, gate leaf, end girders, hoisting brackets,steel track plates ,bronze bush ,stainless steel axles and nut ,bolts ,rubber seal etc complete including cost of all materials with all leads and lifts and as directed by Engineer-in-charge of work. | Erection ,Testing and Commissioning of Gate leaf with Portal frame including embedde parts for 7 Nos. of 3.7 m x 1.2 m size automatic gates including fulcrum assemblies, gate leaf, end girders, hoisting brackets,steel track plates ,bronze bush ,stainless steel axles and nut ,bolts ,rubber seal etc complete including cost of all materials with all leads and lifts and as directed by Engineer-in-charge of work. | 7 | No | - | - | Yes | |
| 10 | Design, Fabrication, Supply, transportation at site of Steel Service Bridge with GI pipe railing for of 3.7m x 1.2m size automatic gates Including cost of all materials, etc. complete as directed by Engineer-in-charge. | Design, Fabrication, Supply, transportation at site of Steel Service Bridge with GI pipe railing for of 3.7m x 1.2m size automatic gates Including cost of all materials, etc. complete as directed by Engineer-in-charge. | 7 | No | - | - | Yes | |
| 11 | Erection, testing & commissioning of Steel Service Bridge with GI pipe railing for of 3.7m x 1.2m size automatic gates Including cost of all materials, etc. complete as directed by Engineer-in-charge. | Erection, testing & commissioning of Steel Service Bridge with GI pipe railing for of 3.7m x 1.2m size automatic gates Including cost of all materials, etc. complete as directed by Engineer-in-charge. | 7 | No | - | - | Yes | |
| 12 | Design, Fabrication, supply, transportation at site of Low Level Friction Damper for 14 Nos. of 3.7m x 1.2m size automatic Gates including Lever Arm, Box for shoe, friction track, disc spring, damper etc. complete including cost of all materials with all leads & lifts as directed by the Engineer in Charge. | Design, Fabrication, supply, transportation at site of Low Level Friction Damper for 14 Nos. of 3.7m x 1.2m size automatic Gates including Lever Arm, Box for shoe, friction track, disc spring, damper etc. complete including cost of all materials with all leads & lifts as directed by the Engineer in Charge. | 14 | No | - | - | Yes | |
| 13 | Erection, testing & commissioning of Low Level Friction Damper for 14 Nos. of 3.7m x 1.2m size automatic Gates including Lever Arm, Box for shoe, friction track, disc spring, damper etc. complete including cost of all materials with all leads & lifts as directed by the Engineer in Charge. | Erection, testing & commissioning of Low Level Friction Damper for 14 Nos. of 3.7m x 1.2m size automatic Gates including Lever Arm, Box for shoe, friction track, disc spring, damper etc. complete including cost of all materials with all leads & lifts as directed by the Engineer in Charge. | 14 | No | - | - | Yes | |
| 14 | Design, Manufacture, Supply, transportation to site of 6 set of Portable Emergency Hydraulic Hoisting System for Automated Gates consisting of Hydraulic cylinder pump, hoses etc. complete including cost of all materials with all leads & lifts as directed by the Engineer in Charge. | Design, Manufacture, Supply, transportation to site of 6 set of Portable Emergency Hydraulic Hoisting System for Automated Gates consisting of Hydraulic cylinder pump, hoses etc. complete including cost of all materials with all leads & lifts as directed by the Engineer in Charge. | 2 | No | - | - | Yes | |
| 15 | Erection, testing & commissioning of 6set of Portable Emergency Hydraulic Hoisting System for Automated Gates consisting of Hydraulic cylinder pump, hoses etc. complete including cost of all materials with all leads & lifts as directed by the Engineer in Charge. | Erection, testing & commissioning of 6set of Portable Emergency Hydraulic Hoisting System for Automated Gates consisting of Hydraulic cylinder pump, hoses etc. complete including cost of all materials with all leads & lifts as directed by the Engineer in Charge. | 2 | No | - | - | Yes | |
| 16 | Providing Operation and Maintenance with Security of Complete System for 36 months (3 Years) round the clock including spares on Free of Cost Basis Complete job as per requirement and direction of E/I. | Providing Operation and Maintenance with Security of Complete System for 36 months (3 Years) round the clock including spares on Free of Cost Basis Complete job as per requirement and direction of E/I. | 3 | Year | - | - | Yes | |
| 17 | Providing Oiling ,Greasing and General Maintenance of Complete System for 36 months (3 Years). | Providing Oiling ,Greasing and General Maintenance of Complete System for 36 months (3 Years). | 3 | Year | - | - | Yes | |
| 18 | Provision for cost of Groove cutting/Concrete breaking in P:C:C/R:C:C by mech instrument or manually for proper anchoring of embeded bottom seal beam etc.all cost of all materials with all leads & lifts as directed by the Engineer in Charge. | Provision for cost of Groove cutting/Concrete breaking in P:C:C/R:C:C by mech instrument or manually for proper anchoring of embeded bottom seal beam etc.all cost of all materials with all leads & lifts as directed by the Engineer in Charge. | 30 | CUM | - | - | Yes | |
| 19 | Providing and laying in Situ M20 Cement concrete in bottom and side groove of gate , including centering and shuttering from work including machine,mixing, laying,vibrating, curing with all leads and lifts, loading and unloading including the cost of all materials equipment, labour etc complete as per specifications and direction of Engineer in charge for CC 1:1.5:3 (M20). | Providing and laying in Situ M20 Cement concrete in bottom and side groove of gate , including centering and shuttering from work including machine,mixing, laying,vibrating, curing with all leads and lifts, loading and unloading including the cost of all materials equipment, labour etc complete as per specifications and direction of Engineer in charge for CC 1:1.5:3 (M20). | 30 | CUM | - | - | Yes | |
| 20 | Drilling of holes of required size for installation of Anchor Bolts/Bars by usage of suitable template and Supply & fixing of Anchor bolts/bars accurately by usage of suitable template and using cementotious bonding material & it includes all lead & lift etc., as directed by Engineer-in-charge. | Drilling of holes of required size for installation of Anchor Bolts/Bars by usage of suitable template and Supply & fixing of Anchor bolts/bars accurately by usage of suitable template and using cementotious bonding material & it includes all lead & lift etc., as directed by Engineer-in-charge. | 7 | G | - | - | Yes |
🤖 AI-Powered Bidder Prediction
Discover companies most likely to bid on this tender
Explore More Opportunities
Unlock Tender Documents
Sign up now to access all documents
Documents 7
1. NIQ KAO WEIR.docx
GENERAL_DOCUMENT
2. SBD KAO WEIR.doc
GENERAL_DOCUMENT
1 NIQ 03-2021-22 KAO WEIR.docx
GENERAL_DOCUMENT
2 SBD NIQ 03-2021-22 KAO WEIR.doc
GENERAL_DOCUMENT
3 TECHNICAL SHEET NIQ 03-2021-22 KAO WEIR.xls
GENERAL_DOCUMENT
VIEW ONLY BOQ N.I.Q. 03-2021-22.xlsx
BOQ
Corrigendum Lt. No. 1003, 11-12-2021.pdf
CORRIGENDUM