Tender Notice for Excavation,Earthfilling,RCCbreaking,PCC,RCC,SANDFILLING,STEELREINFORCEMENT,SHUTTERINGBELOWPLINTHLEV in CUDDAPAH, ANDHRA PRADESH

Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. 2.6.1 All kinds of soil

Demolishing R.C.C. work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 metres lead as per direction of Engineer - in- charge.

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level - 1-1.5-3 (1 cement - 1.5 coarse sand (zone-III)- 3 graded stone aggregate 20 mm nominal size)

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level and below plinth level.5.22A.6 Thermo-Mechanically Treated bars of grade Fe-500D or more

Centering and shuttering including strutting, propping etc. and removal of form as per directions of Engineer-in-charge at all leads and lift 5.9.6 Columns, Pillars, Piers, Abutments, Posts and Struts, (All the above Plinth level)

Providing and Grouting of pockets with cementitious grout Non Shrink of approved make by suitable means Free flowing pump curing etc Complete as per directions of Engineer in charge The payment shall be made on the basis of actual weight of approved grout used as per directions of Engineer in charge

Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge 15.7.4 In cement mortar

Finishing walls with textured exterior paint of required shade - 13.45.1 New work (Two or more coats applied at 3.28 ltr/10 sqm) over and including priming coat of exterior primer applied at 2.20kg/ 10 sqm

15 mm cement plaster with mix -1-6 (1 cement- 6 fine sand) at all heights and lead as per directions of Engineer-in-charge.

Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer.

Designing of RCC foundation forPERISTALTIC PUMP FOR DECANTER SOLID DISCHARGE REPULPER TANK TO SDU DISSOLUTION TANK 65/65

Designing of RCC foundation for Centrifuge feed Pump with VFD Alloy 20 80/40

Designing of RCC foundation for Screw Pump

Designing of RCC foundation for Cloth Wash Water Pump with Motor (4.3 LPM at4 bar)

Designing of RCC foundation for Acidified water feed pump Alloy 20 for cake wash 50/40

Designing of RCC foundation for AI filtrate to dissolution by pump Alloy 20 50/25

Designing of RCC foundation for Cloth wash water transfer pump Alloy 20 50/25

Designing of RCC foundation for PERISTALTIC PUMP FOR pumping to thickener with VFD 65/65

Designing of RCC foundation for Flocculant Dosing Pump

Designing of RCC foundation for PERISTALTIC PUMP FOR H2O2 Peristaltic pump with VFD 40/40

Designing of RCC foundation for PERISTALTIC PUMP FOR Pump to Existing HBF repulping and washing tank with VFD 40/40

Designing of RCC foundation for Cold water from cooling tower to Rotary kiln pump CF8

Designing of RCC foundation for H2O2 Sump- Pumps 80/40

Designing of RCC foundation for Hot water insulated tank -SS 304L

Designing of RCC foundation for Decantor filtrate tank- SS-304L

Designing of RCC foundation for H2SO4 Tank, 2m3 MS

Designing of RCC foundation for Centrifuge Solid Discharge i.e AI Repulper tank SS316L

Designing of RCC foundation for Acidified water Day tank SS316L

Designing of RCC foundation for Cloth wash tank SS316L

Designing of RCC foundation for 15m3 Precipitation Tank ( Elevated Floor) SS316L

Designing of RCC foundation for NaoH tanks -SS316L

Designing of RCC foundation for H2O2 unloading & Transfer tanks

Designing of RCC foundation for Agitator for SDU Repulping Tank, 3 No. of capacity 10m3 (2.2 m Dia X 2.9 m H)

Designing of RCC foundation for Agitated Solid Discharge tank for Decantor Solids with agitator 1No -SS-304L

Designing of RCC foundation for Agitated 15m3 Dissolution tank (EF) -SS316L

Designing of RCC foundation for Agitated Cloth wash tank SS316L

Designing of RCC foundation for Agitated Thickener u/f tank SS316L

Designing of RCC foundation for Centrifuge

Designing of RCC foundation for Rotary kiln

Designing of RCC foundation for Bag filter

Designing of RCC foundation for Pull fan

Designing of RCC foundations,design of Structural supports at 4.3 meter level for supporting tanks, centrifugal decantors, tower press etc.. ,on platform

Erection along with alignment of PERISTALTIC PUMP FOR Existing tank New 8V-2C/D/C with VFD 80/80

Erection along with alignment of Centrifugal pump for pumping Decanter Centrate to SDU thickener 80/40

Erection along with alignment of PERISTALTIC PUMP FOR H2SO4 Dosing with VFD 40/40

Erection along with alignment of Pump from Liquid Centrate tank to Precipitation tank Alloy 20 80/40

Erection along with alignment of Squeezing water Pump with Motor

Erection along with alignment of Press filter feed pump with VFD Centrifugal Alloy 20 40/25

Erection along with alignment of PERISTALTIC PUMP FOR Underflow with VFD 40/40

Erection along with alignment of Cloth wash thickener overflow transfer pump Alloy 20 50/25

Erection along with alignment of Flocculant Transfer Pump

Erection along with alignment of PERISTALTIC PUMP FOR NaoH Peristaltic pump with VFD 40/40

Erection along with alignment of PERISTALTIC PUMP FOR Thickener u/f pump with VFD 65/65

Erection along with alignment of Hot water from rotary kiln to cooling tower pump CF8

Erection along with alignment of H2O2 Unloading Pumps 80/50

Erection along with alignment of H2O2 Transfer Pumps 80/50

Erection along with alignment ofSolid Discharge tank for Decantor Solids with agitator 1No -SS-304L

Erection along with alignment of 15m3 Dissolution tank (EF) -SS316L

Erection along with alignment of Liquid Centrate Tank, 15 m3 -SS316L

Erection along with alignment of AI Filtrate tank,2.0 m3 SS316L

Erection along with alignment of High Density Spillage Thickener 1mX 2.4 mSWD, 15degree slope SS 316L

Cloth wash Thickener overflow tank -SS-304L

Erection along with alignment of High Density Thickener 4mX 3m SWD SS 316L

Erection along with alignment of H2O2 tank -SS316L

Erection along with alignment of Thickener u/f tank SS316L

Erection along with alignment of Agitated Hot water insulated tank -SS 304L

Erection along with alignment of Agitated Decantor filtrate tank- SS-304L

Erection along with alignment of Agitated Centrifuge Solid Discharge i.e AI Repulper tank SS316L

Erection along with alignment of Agitated 15m3 Precipitation Tank ( Elevated Floor) SS316L

Erection along with alignment of Decantor

Erection along with alignment of Press filter

Erection along with alignment of Compressor

Erection along with alignment of Pushh fan

Erection along with alignment of Area Sump pumps

Roof sheeting work (To be billed after completion of full work only) erection

Erection along with alignment of Capacity 2MT, rope length - 12 meters

Erection along with alignment of Electric hoist Capacity 2MT, rope length - 12 meters

Supply of Roof sheets - sheets of sizes 0.55mm thick , along with 2 number of 4 turbo ventilators

Supply of Electric hoist Capacity 2MT, rope length - 12 meters

Design of pipeline routing for process ,steam and instrumentation air and structural support.

Erection of product holding tank.

Design of bag filter suction duct