Procurement Opportunity: Provision for Complete design, drawing, fabrication ,supply, Erection and commissioning of 1st stage, 2nd stage embedded parts for bottom seal sheet, wheel track, And side seal sheet, for each vent of Trash rack With all accessories as per the site requirement including cost of all materials, Machinery, labour, aligning, anchoring, welding, finishing cleaning etc. Applying one coat of zinc rich Epoxy primer and four coats of cold applied coal tar Epoxy Paint including complete job as per specification and approved drawings with all leads lifts also inclusive of all applicable taxes as per direction of E/I. in BIHAR
Bid Publish Date
22-Aug-2022, 1:01 pm
Bid End Date
29-Aug-2022, 5:00 pm
EMD
₹1,73,100
Value
₹0
Location
Progress
Tender Type
Open
Tender Fee
₹10,000
Tender Fee Exemption
No
EMD Exemption
No
Category
MECHANICAL
Categories
30
Public procurement opportunity for The issuing authority Provision for Design, Drawing, Fabrication, Erection, Transportation & Installation all complete of Trash Rack at Dhory Siphon of Western Kosi Main Canal at RD. 130. 40 (U/S & D/S) Under W. K. C. Division Khajauli. in BIHAR issued by. Submission Deadline: 29-08-2022 17: 00: 00. View full details and respond.
Additional Tender Data
Commercial Details
Processing Fee
₹590
Tender Currency
INR
Bid Currency
INR
Ranking Sequence
L1 Ranking
Estimated Value Visibility
N
Bid To RA
No
Authority & Contact
Organization Hierarchy
Government of Bihar->Water Resources Department->C.E. ( MECH.) PATNA->IRRIGATION MECHANICAL CIRCLE, BIRPUR
Approving Authority
SHREEKANT SHUKLA (SE)
Tender Creator
Mr SHREEKANT SHUKLA (SUPERINTENDENT ENGINEER)
Pre-Bid & Qualification
Pre-Bid Discussion Type
Not Required
Payment Breakdown
| Type | Amount | Currency | Mode | Exemption |
|---|---|---|---|---|
| EMD | ₹1,73,100 | INR | Internet Payment Gateway(IPG),Challan|Bank Guarantee | No |
| Tender Fee | ₹10,000 | INR | Internet Payment Gateway(IPG),Challan| | No |
| Tender Processing Fee | ₹590 | INR | Internet Payment Gateway(IPG),Challan| | No |
Document Requirements
Earnest Money
Registration No.
Udyog Aadhaar /Udyam (Ministry of Micro, small & Medium Enterprises) registration certificate No.
Key Equipment (Affidavit of Either owned or leased or by procurement)
Performance Certificate of Similar nature of work as per letter no. 686 dt. 19.08.2014 of W.R.D.
Affidavit
List of Technical Personal
PAN Card
G.S.T. Registration
N.O.C of Debar
Factory Licence
Character Certificate
Additional document required as per mentioned NIQ and Tender Document if required
General Particulars
Earnest Money
Registration No.
Udyog Aadhaar /Udyam (Ministry of Micro, small & Medium Enterprises) registration certificate No.
Key Equipment (Affidavit of Either owned or leased or by procurement)
Performance Certificate of Similar nature of work as per letter no. 686 dt. 19.08.2014 of W.R.D.
Affidavit
List of Technical Personal
PAN Card
G.S.T. Registration
N.O.C of Debar
Factory Licence
Character Certificate
Tender Terms
Section 1
DetailsAccepted all terms and conditions as per mentioned NIQ and Tender Document.
Section 1
DetailsAccepted all terms and conditions as per mentioned NIQ and Tender Document.
Accepted all terms and conditions as per mentioned NIQ and Tender Document.
Authority Records
BID & GeM Expert Consultancy
End-to-end support — bid preparation, GeM registration, document filing & compliance by industry experts.
Free consultation · 24h response
Documents 6
design of Dhory siphon.pdf
GENERAL_DOCUMENT
hydraulic data for trash rack.docx
GENERAL_DOCUMENT
Technical bid for trash rack.xls
GENERAL_DOCUMENT
Financial bid for trash rack.xlsx
GENERAL_DOCUMENT
NIQ Document.docx
GENERAL_DOCUMENT
Trash rack.pdf
GENERAL_DOCUMENT
Bill of Quantities (BOQ)
9 Items Sign in to view GEM price trends Sign in for GEM prices
Provision for Complete design, drawing, fabrication ,supply, Erection and commissioning of 1st stage, 2nd stage embedded parts for bottom seal sheet, wheel track, And side seal sheet, for each vent of Trash rack With all accessories as per the site requirement including cost of all materials, Machinery, labour, aligning, anchoring, welding, finishing cleaning etc. Applying one coat of zinc rich Epoxy primer and four coats of cold applied coal tar Epoxy Paint including complete job as per specification and approved drawings with all leads lifts also inclusive of all applicable taxes as per direction of E/I.
Provision for Complete design, drawing, fabrication ,supply, Erection and commissioning of 1st stage, 2nd stage embedded parts for bottom seal sheet, wheel track, And side seal sheet, for each vent of Trash rack With all accessories as per the site requirement including cost of all materials, Machinery, labour, aligning, anchoring, welding, finishing cleaning etc. Applying one coat of zinc rich Epoxy primer and four coats of cold applied coal tar Epoxy Paint including complete job as per specification and approved drawings with all leads lifts also inclusive of all applicable taxes as per direction of E/I.
Provision of 2nd stage concreting of embedded parts of all the gates by providing and laying PCC or RCC M-150 with nominal mix of (1:2:4) in block outs for making gate grooves with approved quality of qraded coarse aggregate of required grade and approved quality of sand of requisite F.M. washed and screened and also include some concrete breaking for fixing or installing the 2nd stage components firmly at their respective positions as per the site requirement and design With the necessary tools and plants curing, including cost of form work as well reinforcement ,its cutting, bending ,binding and placing including royalty and carriage with all cost of labor and material also inclusive of all applicable taxes as per specification and direction of E/I.
Provision of 2nd stage concreting of embedded parts of all the gates by providing and laying PCC or RCC M-150 with nominal mix of (1:2:4) in block outs for making gate grooves with approved quality of qraded coarse aggregate of required grade and approved quality of sand of requisite F.M. washed and screened and also include some concrete breaking for fixing or installing the 2nd stage components firmly at their respective positions as per the site requirement and design With the necessary tools and plants curing, including cost of form work as well reinforcement ,its cutting, bending ,binding and placing including royalty and carriage with all cost of labor and material also inclusive of all applicable taxes as per specification and direction of E/I.
Provision for earth work in marshy, slushy and daldal soil along with dewatering through suitable pump for cleaning the vents as per the requirement of site with all cost of labour and material also inclusive of all applicable taxes as per specification and direction of E/I.
Provision for earth work in marshy, slushy and daldal soil along with dewatering through suitable pump for cleaning the vents as per the requirement of site with all cost of labour and material also inclusive of all applicable taxes as per specification and direction of E/I.
Provision for Complete design, drawing, fabrication, supply, Erection and commissioning of Trash rack 10 Nos. consisting of equally spaced trash rack vertical bars, frame, vertical &horizontal member, wheel pin, bearing ,with all accessories including cost of all materials, Machinery, labour, aligning, anchoring, welding, finishing cleaning etc. Applying Two coat of zinc rich Epoxy primer and four coats of cold applied coal tar Epoxy Paint including Required civil work with carriage concreting and (also Designed as per Latest B.I.S Code With amendment if Any) complete as per specification and approved drawings with all leads lifts also inclusive of all applicable taxes as per direction of E/I
Provision for Complete design, drawing, fabrication, supply, Erection and commissioning of Trash rack 10 Nos. consisting of equally spaced trash rack vertical bars, frame, vertical &horizontal member, wheel pin, bearing ,with all accessories including cost of all materials, Machinery, labour, aligning, anchoring, welding, finishing cleaning etc. Applying Two coat of zinc rich Epoxy primer and four coats of cold applied coal tar Epoxy Paint including Required civil work with carriage concreting and (also Designed as per Latest B.I.S Code With amendment if Any) complete as per specification and approved drawings with all leads lifts also inclusive of all applicable taxes as per direction of E/I
Provision for the Complete design, drawing, fabrication, supply, Erection and commissioning of Hoist bridge beam , Hoist Platform consisting of main girder, cross girder, chequred plate covering, hand railing etc.(On both Sides i.e U/S & D/S) with all other accessories as per the requirement of site for supporting hoist for operating all the gates including cost of all materials, Machinery, labour, aligning, anchoring, welding, finishing cleaning etc. Applying Two coat of zinc rich Epoxy primer and four coats of cold applied coal tar Epoxy Paint including Required civil work with carriage concreting and (also Designed as per Latest B.I.S Code With amendment if Any) complete as per specification and approved drawings with all leads lifts also inclusive of all applicable taxes as per direction of E/I.
Provision for the Complete design, drawing, fabrication, supply, Erection and commissioning of Hoist bridge beam , Hoist Platform consisting of main girder, cross girder, chequred plate covering, hand railing etc.(On both Sides i.e U/S & D/S) with all other accessories as per the requirement of site for supporting hoist for operating all the gates including cost of all materials, Machinery, labour, aligning, anchoring, welding, finishing cleaning etc. Applying Two coat of zinc rich Epoxy primer and four coats of cold applied coal tar Epoxy Paint including Required civil work with carriage concreting and (also Designed as per Latest B.I.S Code With amendment if Any) complete as per specification and approved drawings with all leads lifts also inclusive of all applicable taxes as per direction of E/I.
Provision for the Complete design, drawing, fabrication, supply, Erection and commissioning of structural steel Ladder( 2 Nos.- 1 No. in U/S & 1 No. in D/S) Consisting of Main girder, Angle post, Hand Railing & ladder step thread with suitable size and Frames & chequered plate as per requirement of site. Also applying Two coat of zinc rich Epoxy primer and four coats of cold applied coal tar Epoxy Paint including Required civil work with carriage concreting and (also Designed as per Latest B.I.S Code With amendment if Any) complete as per specification and approved drawings with all leads lifts also inclusive of all applicable taxes as per direction of E/I.
Provision for the Complete design, drawing, fabrication, supply, Erection and commissioning of structural steel Ladder( 2 Nos.- 1 No. in U/S & 1 No. in D/S) Consisting of Main girder, Angle post, Hand Railing & ladder step thread with suitable size and Frames & chequered plate as per requirement of site. Also applying Two coat of zinc rich Epoxy primer and four coats of cold applied coal tar Epoxy Paint including Required civil work with carriage concreting and (also Designed as per Latest B.I.S Code With amendment if Any) complete as per specification and approved drawings with all leads lifts also inclusive of all applicable taxes as per direction of E/I.
Provision for the Complete design, drawing, fabrication, supply, Erection and commissioning of worm and worm wheel/Hoist-nut and hoist stem (Spindle) hoist system of adequate capacity consisting of base frame, connecting shaft, coupling standard make reduction gear system etc.as per requirement at site with all accessories for easy operation of all Trash rack including costs of all materials, Machinery, labour, aligning, anchoring, welding, finishing cleaning etc. Applying Two coat of zinc chromate red oxide primer and four coats of cold applied coal tar Epoxy Paint also inclusive of all applicable taxes as per specification and approved drawing and direction of E/I.
Provision for the Complete design, drawing, fabrication, supply, Erection and commissioning of worm and worm wheel/Hoist-nut and hoist stem (Spindle) hoist system of adequate capacity consisting of base frame, connecting shaft, coupling standard make reduction gear system etc.as per requirement at site with all accessories for easy operation of all Trash rack including costs of all materials, Machinery, labour, aligning, anchoring, welding, finishing cleaning etc. Applying Two coat of zinc chromate red oxide primer and four coats of cold applied coal tar Epoxy Paint also inclusive of all applicable taxes as per specification and approved drawing and direction of E/I.
8 Nos. Tentative size(4.568m x 4.268m).
8 Nos. Tentative size(4.568m x 4.268m).
2 Nos. Tentative Size(4.42 m x 4.268m).
2 Nos. Tentative Size(4.42 m x 4.268m).
| Item # | Title | Description | Quantity | Unit | Consignee | Delivery (Days) | Mandatory | Price Trends |
|---|---|---|---|---|---|---|---|---|
| 1 | Provision for Complete design, drawing, fabrication ,supply, Erection and commissioning of 1st stage, 2nd stage embedded parts for bottom seal sheet, wheel track, And side seal sheet, for each vent of Trash rack With all accessories as per the site requirement including cost of all materials, Machinery, labour, aligning, anchoring, welding, finishing cleaning etc. Applying one coat of zinc rich Epoxy primer and four coats of cold applied coal tar Epoxy Paint including complete job as per specification and approved drawings with all leads lifts also inclusive of all applicable taxes as per direction of E/I. | Provision for Complete design, drawing, fabrication ,supply, Erection and commissioning of 1st stage, 2nd stage embedded parts for bottom seal sheet, wheel track, And side seal sheet, for each vent of Trash rack With all accessories as per the site requirement including cost of all materials, Machinery, labour, aligning, anchoring, welding, finishing cleaning etc. Applying one coat of zinc rich Epoxy primer and four coats of cold applied coal tar Epoxy Paint including complete job as per specification and approved drawings with all leads lifts also inclusive of all applicable taxes as per direction of E/I. | 10 | each | - | - | Yes | |
| 2 | Provision of 2nd stage concreting of embedded parts of all the gates by providing and laying PCC or RCC M-150 with nominal mix of (1:2:4) in block outs for making gate grooves with approved quality of qraded coarse aggregate of required grade and approved quality of sand of requisite F.M. washed and screened and also include some concrete breaking for fixing or installing the 2nd stage components firmly at their respective positions as per the site requirement and design With the necessary tools and plants curing, including cost of form work as well reinforcement ,its cutting, bending ,binding and placing including royalty and carriage with all cost of labor and material also inclusive of all applicable taxes as per specification and direction of E/I. | Provision of 2nd stage concreting of embedded parts of all the gates by providing and laying PCC or RCC M-150 with nominal mix of (1:2:4) in block outs for making gate grooves with approved quality of qraded coarse aggregate of required grade and approved quality of sand of requisite F.M. washed and screened and also include some concrete breaking for fixing or installing the 2nd stage components firmly at their respective positions as per the site requirement and design With the necessary tools and plants curing, including cost of form work as well reinforcement ,its cutting, bending ,binding and placing including royalty and carriage with all cost of labor and material also inclusive of all applicable taxes as per specification and direction of E/I. | 10 | each | - | - | Yes | |
| 3 | Provision for earth work in marshy, slushy and daldal soil along with dewatering through suitable pump for cleaning the vents as per the requirement of site with all cost of labour and material also inclusive of all applicable taxes as per specification and direction of E/I. | Provision for earth work in marshy, slushy and daldal soil along with dewatering through suitable pump for cleaning the vents as per the requirement of site with all cost of labour and material also inclusive of all applicable taxes as per specification and direction of E/I. | 10 | each | - | - | Yes | |
| 4 | Provision for Complete design, drawing, fabrication, supply, Erection and commissioning of Trash rack 10 Nos. consisting of equally spaced trash rack vertical bars, frame, vertical &horizontal member, wheel pin, bearing ,with all accessories including cost of all materials, Machinery, labour, aligning, anchoring, welding, finishing cleaning etc. Applying Two coat of zinc rich Epoxy primer and four coats of cold applied coal tar Epoxy Paint including Required civil work with carriage concreting and (also Designed as per Latest B.I.S Code With amendment if Any) complete as per specification and approved drawings with all leads lifts also inclusive of all applicable taxes as per direction of E/I | Provision for Complete design, drawing, fabrication, supply, Erection and commissioning of Trash rack 10 Nos. consisting of equally spaced trash rack vertical bars, frame, vertical &horizontal member, wheel pin, bearing ,with all accessories including cost of all materials, Machinery, labour, aligning, anchoring, welding, finishing cleaning etc. Applying Two coat of zinc rich Epoxy primer and four coats of cold applied coal tar Epoxy Paint including Required civil work with carriage concreting and (also Designed as per Latest B.I.S Code With amendment if Any) complete as per specification and approved drawings with all leads lifts also inclusive of all applicable taxes as per direction of E/I | - | - | - | - | Yes | |
| 5 | Provision for the Complete design, drawing, fabrication, supply, Erection and commissioning of Hoist bridge beam , Hoist Platform consisting of main girder, cross girder, chequred plate covering, hand railing etc.(On both Sides i.e U/S & D/S) with all other accessories as per the requirement of site for supporting hoist for operating all the gates including cost of all materials, Machinery, labour, aligning, anchoring, welding, finishing cleaning etc. Applying Two coat of zinc rich Epoxy primer and four coats of cold applied coal tar Epoxy Paint including Required civil work with carriage concreting and (also Designed as per Latest B.I.S Code With amendment if Any) complete as per specification and approved drawings with all leads lifts also inclusive of all applicable taxes as per direction of E/I. | Provision for the Complete design, drawing, fabrication, supply, Erection and commissioning of Hoist bridge beam , Hoist Platform consisting of main girder, cross girder, chequred plate covering, hand railing etc.(On both Sides i.e U/S & D/S) with all other accessories as per the requirement of site for supporting hoist for operating all the gates including cost of all materials, Machinery, labour, aligning, anchoring, welding, finishing cleaning etc. Applying Two coat of zinc rich Epoxy primer and four coats of cold applied coal tar Epoxy Paint including Required civil work with carriage concreting and (also Designed as per Latest B.I.S Code With amendment if Any) complete as per specification and approved drawings with all leads lifts also inclusive of all applicable taxes as per direction of E/I. | 1 | each | - | - | Yes | |
| 6 | Provision for the Complete design, drawing, fabrication, supply, Erection and commissioning of structural steel Ladder( 2 Nos.- 1 No. in U/S & 1 No. in D/S) Consisting of Main girder, Angle post, Hand Railing & ladder step thread with suitable size and Frames & chequered plate as per requirement of site. Also applying Two coat of zinc rich Epoxy primer and four coats of cold applied coal tar Epoxy Paint including Required civil work with carriage concreting and (also Designed as per Latest B.I.S Code With amendment if Any) complete as per specification and approved drawings with all leads lifts also inclusive of all applicable taxes as per direction of E/I. | Provision for the Complete design, drawing, fabrication, supply, Erection and commissioning of structural steel Ladder( 2 Nos.- 1 No. in U/S & 1 No. in D/S) Consisting of Main girder, Angle post, Hand Railing & ladder step thread with suitable size and Frames & chequered plate as per requirement of site. Also applying Two coat of zinc rich Epoxy primer and four coats of cold applied coal tar Epoxy Paint including Required civil work with carriage concreting and (also Designed as per Latest B.I.S Code With amendment if Any) complete as per specification and approved drawings with all leads lifts also inclusive of all applicable taxes as per direction of E/I. | 2 | each | - | - | Yes | |
| 7 | Provision for the Complete design, drawing, fabrication, supply, Erection and commissioning of worm and worm wheel/Hoist-nut and hoist stem (Spindle) hoist system of adequate capacity consisting of base frame, connecting shaft, coupling standard make reduction gear system etc.as per requirement at site with all accessories for easy operation of all Trash rack including costs of all materials, Machinery, labour, aligning, anchoring, welding, finishing cleaning etc. Applying Two coat of zinc chromate red oxide primer and four coats of cold applied coal tar Epoxy Paint also inclusive of all applicable taxes as per specification and approved drawing and direction of E/I. | Provision for the Complete design, drawing, fabrication, supply, Erection and commissioning of worm and worm wheel/Hoist-nut and hoist stem (Spindle) hoist system of adequate capacity consisting of base frame, connecting shaft, coupling standard make reduction gear system etc.as per requirement at site with all accessories for easy operation of all Trash rack including costs of all materials, Machinery, labour, aligning, anchoring, welding, finishing cleaning etc. Applying Two coat of zinc chromate red oxide primer and four coats of cold applied coal tar Epoxy Paint also inclusive of all applicable taxes as per specification and approved drawing and direction of E/I. | 10 | each | - | - | Yes | |
| 4 (a) | 8 Nos. Tentative size(4.568m x 4.268m). | 8 Nos. Tentative size(4.568m x 4.268m). | 8 | each | - | - | Yes | |
| 4 (b) | 2 Nos. Tentative Size(4.42 m x 4.268m). | 2 Nos. Tentative Size(4.42 m x 4.268m). | 2 | each | - | - | Yes |
🤖 AI-Powered Bidder Prediction
Discover companies most likely to bid on this tender
Explore More Opportunities
Unlock Tender Documents
Sign up now to access all documents
Documents 6
design of Dhory siphon.pdf
GENERAL_DOCUMENT
hydraulic data for trash rack.docx
GENERAL_DOCUMENT
Technical bid for trash rack.xls
GENERAL_DOCUMENT
Financial bid for trash rack.xlsx
GENERAL_DOCUMENT
NIQ Document.docx
GENERAL_DOCUMENT
Trash rack.pdf
GENERAL_DOCUMENT