Bid Publish Date
28-Jun-2026, 2:14 pm
Bid End Date
21-Jul-2026, 3:00 pm
Value
₹4,50,000
Location
Progress
Quantity
1802
Category
Repairing the condensate tank pump delivery line of the pan 1
Bid Type
Two Packet Bid
Uttar Pradesh Cooperative Sugar Factories Federation Limited invites bids for a broad procurement with an estimated value of ₹450,000 in BIJNOR, UTTAR PRADESH 246701. The tender covers multiple line items (193 BOQ entries reported as N/A), with an option clause allowing ±25% quantity variation at contracted rates. All bidders must meet turnover, experience proof, and certificate submission requirements as outlined in the ATC. The opportunity emphasizes compliance, record accuracy, and timely delivery within contract terms.
Key Term 1: Quantity variation allowed up to 25% during contract
Key Term 2: Turnover criteria requires audited statements or CA certificate
Key Term 3: Documentation and certificates must be uploaded; non-submission risks rejection
Not explicitly stated; verify in Bid Document/ATC for EMD, payment schedule, and any advance payments
Delivery period starts from the last date of original delivery order; extended time calculated as (increased quantity / original quantity) × original delivery period, min 30 days
Not specified in data; check ATC for LD or performance bond requirements
Minimum average turnover over the last three financial years as per bid document
Past project experience proof via contract copies or client certifications
Submission of required GST, PAN, and technical/certification documents
Tender Category
Goods
Bid To RA
No
Bid To RA Enabled
Yes
Payment Timelines
Payments shall be made to the Seller within 45 days of issue of consignee receipt-cum-acceptance certificate (CRAC) and on-line submission of bills (This is in supersession of 10 days time as provided in clause 12 of GeM GTC)
Max Delivery Days
90
Delivery Locations
1
Delivery Cities
Bijnor
Delivery Pincodes
246763
| Consignee | Address | City | State | Pincode | Quantity | Delivery Days | Additional Requirement |
|---|---|---|---|---|---|---|---|
| Anurag Singh | 246763,KISAN SAHKARI CHINI MILLS LTD., Sneh Road Najibabad PIN CODE- 246763 GST NO - 09AAAAK1634P1ZD Contact no- 9411427852,6397805612 | Bijnor | Uttar Pradesh | 246763 | 2 | 90 | - |
End-to-end support — bid preparation, GeM registration, document filing & compliance by industry experts.
Free consultation · 24h response
Main Document
BOQ
BOQ
GEM_GENERAL_TERMS_AND_CONDITIONS
N/A
North Tripura, TRIPURA
N/A
Unakoti, TRIPURA
Delhi University
NORTH, DELHI
Indian Army
LEH, JAMMU & KASHMIR
N/A
CENTRAL, DELHI
Tender Results
Loading results...
Repairing the condensate tank pump delivery line of the pan 1
Fabricate and install 6inch size nipple
Repairing the condensate tank pump delivery line of the pan 2
Fabricate and install 6inch size flange
Repairing the condensate tank pump delivery line of the pan 3
Dismantling 6inch size pipeline
Replacing damaged bypass line band flange of melter 1
Installing 6inch size pipeline and giving satisfactory trial
Replacing damaged bypass line band flange of melter 2
Fabricate and install 6inch size band
Replacing damaged bypass line band flange of melter 3
Fabricate and install 6inch size flange
Replace damaged 100 pound 3inch size pipeline from Pan No 1 to Pan No 6 and give satisfactory trial
Replace damaged 100 pound 3inch size pipeline from Pan No 1 to Pan No 6 and give satisfactory trial
Replace the weak vapor pipe from Pan No 1 to 6 size dia 1 150 m length 30 m 1
Dismantle the weak vapor pipe from Pan No 1 to 6
Replace the weak vapor pipe from Pan No 1 to 6 size dia 1 150 m length 30 m 2
Fabricate the weak vapor pipe from Pan No 1 to 6
Replace main hole dia 600 mm of Pan No 3 Sevual with 10 mm thick plate
Replace main hole dia 600 mm of Pan No 3 Sevual with 10 mm thick plate
Replace damaged overflow pipeline of BH and CL molasses conditioner of 6inch size 1
Replace damaged overflow pipeline of BH and CL molasses conditioner of 6inch size
Replace damaged overflow pipeline of BH and CL molasses conditioner of 6inch size 2
Fabricate and install 6inch size band
Replace corroded nipples pipes flanges of 6inch size header on Pan No 5 and 6 install related nipples valves etc and give satisfactory trial
Replace corroded nipples pipes flanges of 6inch size header on Pan No 5 and 6 install related nipples valves etc and give satisfactory trial
Replace damaged ammonia pipeline flange nipple in Pan No 4 and 6 1
Replace 2inch size pipeline
Replace damaged ammonia pipeline flange nipple in Pan No 4 and 6 2
Fabricate and install 2inch size flange
Replace damaged ammonia pipeline flange nipple in Pan No 4 and 6 3
Fabricate and install 2inch size nipple
Replace damaged ammonia pipeline flange nipple in Pan No 4 and 6 4
Fabricate and install 3inch size flange
Replace damaged ammonia pipeline flange nipple in Pan No 4 and 6 5
Fabricate and install 3inch size valve
Cut and remove damaged wash-out line installed on the pan and rebuild with supplied pipe and install it 1
Replace and install 6inch size pipeline
Cut and remove damaged wash-out line installed on the pan and rebuild with supplied pipe and install it 2
Fabricate and install 6inch size flange
Replace damaged washing pipeline nipple flange band on Pan No 6 1
Replace 6inch size pipeline of the above
Replace damaged washing pipeline nipple flange band on Pan No 6 2
Fabricate and install 6inch size flange
Replace damaged washing pipeline nipple flange band on Pan No 6 3
Fabricate and install 6inch size nipple
Replace damaged washing pipeline nipple flange band on Pan No 6 4
Fabricate and install 6inch size band
Install valve in steam line at Pan No 2 550 mm 1
Install valve in steam line at Pan No 2 550 mm
Install valve in steam line at Pan No 2 550 mm 2
Install flange in steam line at Pan No 2 550 mm
Install valve in steam line at Pan No 2 550 mm 3
Install nipple in steam line at Pan No 2 550 mm
Install valve in steam line at Pan No 2 550 mm 4
Fabricate and install catcher element size 75 X 75 X 8 angle on Pan No 4 and 5
Replace nipple and band of A heavy tank 2
Replace nipples of the above tank
Replace nipple and band of A heavy tank 3
Replace bands of the above tank
Replace nipple and band of A heavy tank 4
Replace partition of syrup tank with 10/12 mm thick plate
Remove clean and reinstall 4inch size syrup line on pan
Remove clean and reinstall 4inch size syrup line on pan
Cut and remove syrup header and fabricate and install new header
Cut and remove syrup header and fabricate and install new header
Replacing the 6inch size glycol washing line fitted on Pan No 1
Replacing the 6inch size glycol washing line fitted on Pan No 1
Replacing nipples of different lines of Pan No 6 1
Replacing nipples of 2inch size line mentioned above
Replacing nipples of different lines of Pan No 6 2
Replacing nipples of 4inch size line mentioned above
Replacing nipples of different lines of Pan No 6 3
Replacing nipples of 6inch size line mentioned above
Replacing nipples of different lines of Pan No 6 4
Replacing nipples of 8inch size line mentioned above
Replacing 10inch size nipples of cut off line of Pan No 6 1
Replacing 10inch size nipples of cut off line of Pan No 6
Replacing 10inch size nipples of cut off line of Pan No 6 2
Replacing 10inch size pipe line
Replacing 10inch size nipples of cut off line of Pan No 6 3
Making and fitting 10inch size flange
Replacing 10inch size nipples of cut off line of Pan No 6 4
Making and fitting 10inch size band
Replacing corroded hot water pipeline nipples flanges valves in Pan No 4 1
Making and fitting 8inch size band
Replacing corroded hot water pipeline nipples flanges valves in Pan No 4 2
Replacing 4inch size pipe line
Replacing corroded hot water pipeline nipples flanges valves in Pan No 4 3
Making and fitting 4inch size flange
Replacing corroded hot water pipeline nipples flanges valves in Pan No 4 4
Making and fitting 4inch size valve
Fabricating M S bed for syrup pump and motor fitting and alignment followed by satisfactory trial
Fabricating M S bed for syrup pump and motor fitting and alignment followed by satisfactory trial
Dismantling weak condensate bottle of old set
Dismantling weak condensate bottle of old set vertical line juice heater and quad body No 4 disposing to scrap yard fabricating all connections using 8/10 mm plates and giving satisfactory vacuum trial
Replacing weak pipeline flange valve and band of old set vertical juice heater 1
Replacing 2inch size pipeline
Replacing weak pipeline flange valve and band of old set vertical juice heater 2
Replacing 6inch size pipeline
Replacing weak pipeline flange valve and band of old set vertical juice heater 3
Making and fitting 2inch size flange
Replacing weak pipeline flange valve and band of old set vertical juice heater 4
Making and fitting 6inch size flange
Replacing weak pipeline flange valve and band of old set vertical juice heater 5
Making and fitting 6inch size band
Replacing weak pipeline of old Quad set No 4 1
Making and fitting 6inch size valve
Replacing weak pipeline of old Quad set No 4 2
Replacing 2inch size pipeline
Replacing weak pipeline of old Quad set No 4 3
Replacing 6inch size pipeline
Replacing weak pipeline of old Quad set No 4 4
Making and fitting 6inch size band
Replacing weak pipeline of old Quad set No 4 5
Making and fitting 6inch size flange
Dismantling damaged mesh of section pipe located at Injection No 2 and 3 and making a new one from given M S plate and fitting it
Dismantling damaged mesh of section pipe located at Injection No 2 and 3 and making a new one from given M S plate and fitting it
Cutting and discarding old damaged reducer plate of section pipe located at Injection No 2 and 3 and remaking the same
Cutting and discarding old damaged reducer plate of section pipe located at Injection No 2 and 3 and remaking the same
Fitting water line from overhead to service tank 1
Fitting mentioned line into service tank
Fitting water line from overhead to service tank 2
Making and fitting 8inch size band
Details of work of Canti machine No 6 and 7 1
Making and fitting 8inch size nipple
Details of work of Canti machine No 6 and 7 2
Dismantling and fitting 6inch size pipeline
Details of work of Canti machine No 6 and 7 3
Making and fitting 6inch size band
Details of work with new pipes from S Sugarbin 1
Dismantling resistance box installed on spray making and fitting new one from given M M plate carrying out proper stay fitting and welding and conducting leak proof trial
Details of work with new pipes from S Sugarbin 2
Dismantling and installing 8inch size pipeline
Details of work with new pipes from S Sugarbin 3
Fabricating and installing 8inch size bands
Details of work for KCP No 1 and 2 and Canty Machine No 6 and 7 1
Fabricating and installing 8inch size flanges
Details of work for KCP No 1 and 2 and Canty Machine No 6 and 7 2
Dismantling and installing 12inch size pipeline
Details of work for KCP No 1 and 2 and Canty Machine No 6 and 7 3
Fabricating and installing 12inch size bands
Work on hot water line of brown sugar magma 1
Fabricating and installing 12inch size flanges
Work on hot water line of brown sugar magma 2
Dismantling and installing 3inch size pipeline
Work on hot water line of brown sugar magma 3
Manufacturing and installing 3inch size nipples
Work on hot water line of brown sugar magma 4
Manufacturing and installing 3inch size bands
Cutting and removing damaged monitor casing and ribs
Cutting and removing damaged monitor casing and ribs inside Canty No 1 and 2 and KCP Machine 1 and 2 patching with 10/12 mm MS plate and giving satisfactory trial 1
Cutting and removing damaged center shaft and arms inside KCP Machines No 1 and 2 bending and fitting new parts with 8 to 10 mm plate
Cutting and removing damaged center shaft and arms inside KCP Machines No 1 and 2 bending and fitting new parts with 8 to 10 mm plate 1
Dismantling damaged upper cover part of Canty Machine No 6 and 7 scrapping fabricating and fitting new cover with 12 mm plate and making all related connections
Dismantling damaged upper cover part of Canty Machine No 6 and 7 scrapping fabricating and fitting new cover with 12 mm plate and making all related connections
Dismantling damaged part of molasses weighing scale receiving tank and fabricating and fitting new part by bending 8 mm thick plate and depositing scrap in scrap yard
Dismantling damaged part of molasses weighing scale receiving tank and fabricating and fitting new part by bending 8 mm thick plate and depositing scrap in scrap yard
Dismantling damaged plate of sugar discharge chute from sugar elevator to sugar grader and fabricating and fitting new plate of 6 mm thickness depositing scrap in scrap yard
Dismantling damaged plate of sugar discharge chute from sugar elevator to sugar grader and fabricating and fitting new plate of 6 mm thickness depositing scrap in scrap yard
Details of work from C magma to melter tank 1
Modifying sugar chute of grader in dryer house and giving satisfactory trial
Details of work from C magma to melter tank 2
Dismantling and installing 4inch size pipeline
Details of work from C magma to melter tank 3
Fabricating and installing 4inch size flanges
Details of work from C magma to melter tank 4
Manufacturing and installing 4inch size bands
Details of work from C magma to melter tank 5
Manufacturing and installing 4inch size nipples
Repairing work details of final molasses tank 1
Removing transit heater installed on C Centrifugal machine opening side plate for cleaning and hydraulic servicing reinstalling in place and making all connections
Repairing work details of final molasses tank 2
Dismantling and installing 2inch size pipeline
Repairing work details of final molasses tank 3
Fabricating and installing 2inch size flanges
Repairing work details of final molasses tank 4
Manufacturing and installing 2inch size nipples
Repairing work details of final molasses tank 5
Manufacturing and installing 2inch size valves
Details of work from melter to magma line 1
Removing old taper of Sugar Hopper No 1 scrapping it fabricating new one from 3/5 mm MS plate installing and giving satisfactory trial
Details of work from melter to magma line 2
Dismantling and installing 6inch size pipeline
Details of work from melter to magma line 3
Manufacturing and installing 6inch size bands
Details of work for A magma pump 1
Manufacturing and installing 2inch size nipples
Details of work for A magma pump 2
Manufacturing and installing 6inch size bands
Details of work for A magma pump 3
Manufacturing and installing 6inch size flanges
Details of work for A magma pump 4
Manufacturing and installing 5inch size flanges
Details of work for A magma pump 5
Manufacturing and installing 5inch size valves
Details of work at ETP Effluent Treatment Plant1
Removing damaged/weak top and bottom sugar discharge chute of Canty Machine No 4 including flange scrapping fabricating new parts with 6 mm MS plate as per suit sample preparing all connections like angle channel etc fitting on side and giving satisfactory trial
Details of work at ETP Effluent Treatment Plant2
Installing 2inch flow meter
Details of work at ETP Effluent Treatment Plant3
Dismantling the damaged 6inch dia pipeline from primary clarifier to anoxic tank and putting it in scrap yard and installing a new pipeline
Details of work at ETP Effluent Treatment Plant4
Dismantling and installing 4inch size pipeline
Details of work at ETP Effluent Treatment Plant5
Installing 4inch size valve/NRV
Details of work at ETP Effluent Treatment Plant6
Fabricating 4inch size band
Details of work at ETP Effluent Treatment Plant7
Dismantling and installing 2inch size pipeline
Details of work at ETP Effluent Treatment Plant8
Fabricating and installing 2inch size flange
Dismantling the damaged 8inch dia pipeline from aeration tank to secondary tank and putting it in scrap yard
Dismantling the damaged 8inch dia pipeline from aeration tank to secondary tank and putting it in scrap yard
Dismantling diffusers installed in aeration tank and putting them in scrap yard and replacing the throat part
Dismantling diffusers installed in aeration tank and putting them in scrap yard and replacing the throat part
In Sulfate Removal Plant reaction chamber dismantling corroded 6 mm partition plate putting it in scrap yard and fabricating with new 8 mm plate
In Sulfate Removal Plant reaction chamber dismantling corroded 6 mm partition plate putting it in scrap yard and fabricating with new 8 mm plate
Dismantling corroded 2inch size treated water outlet line of ETP and putting in scrap yard and installing new 3inch size line at the same location
Dismantling corroded 2inch size treated water outlet line of ETP and putting in scrap yard and installing new 3inch size line at the same location
Dismantling 800 mm dia exhaust pipe line below turbine with nipple band flange and putting in scrap yard
Dismantling 800 mm dia exhaust pipe line below turbine with nipple band flange and putting in scrap yard
Fabricating 800 mm dia exhaust pipeline below turbine from 12 mm plate by bending and installing at position and providing satisfactory trial
Fabricating 800 mm dia exhaust pipeline below turbine from 12 mm plate by bending and installing at position and providing satisfactory trial
Fabricating 800 mm dia exhaust pipeline below vapor cell 950 wag meter from 12 mm plate by bending and installing at position and providing satisfactory trial
Fabricating 800 mm dia exhaust pipeline below vapor cell 950 wag meter from 12 mm plate by bending and installing at position and providing satisfactory trial
Fabricating 800 mm dia exhaust pipeline below vapor cell 950 wag meter from 12 mm plate by bending into T shape and installing at position and providing satisfactory trial
Fabricating 800 mm dia exhaust pipeline below vapor cell 950 wag meter from 12 mm plate by bending into T shape and installing at position and providing satisfactory trial
Fabricating work
Fabricating 800 mm dia exhaust pipeline dummy/flange from 12 mm plate by bending and installing at position and providing satisfactory trial
Dismantling weak part of semichemiser 1000 wag meter
Dismantling weak part of semichemiser 1000 wag meter warm saser putting scrap in scrap yard fabricating from 12 mm thick plate by bending and installing with related connections and giving satisfactory trial Size dia 3 4 m
Dismantling weak parts of old quad body no 2 and 3 20inch vapor pipe putting scrap in scrap yard fabricating from 8 mm thick plate by bending and installing and providing satisfactory trial
Dismantling weak parts of old quad body no 2 and 3 20inch vapor pipe putting scrap in scrap yard fabricating from 8 mm thick plate by bending and installing and providing satisfactory trial
Dismantling weak parts of vapor pipe 32inch size of vapor cell 1000 wag meter putting scrap in scrap yard fabricating from 8 mm thick plate by bending and installing and providing satisfactory trial
Dismantling weak parts of vapor pipe 32inch size of vapor cell 1000 wag meter putting scrap in scrap yard fabricating from 8 mm thick plate by bending and installing and providing satisfactory trial
Dismantling weak part of 6inch size header of all juice heaters condensate and installing new one
Dismantling weak part of 6inch size header of all juice heaters condensate and installing new one
Removing all partition plates
Removing all partition plates of juice heater header by cutting straight and circular shapes cleaning tube plate completely and fabricating new circular and straight partition plates from 10/12 mm plate installing and preparing header with MS strips as before applying rubber strips and providing satisfactory trial
Cutting out quailons and all related angles
Cutting out quailons and all related angles fixed in clarifier compartments and refitting after completion of work and providing satisfactory trial
Carrying out work on clarifier pipeline 1
Patching inside clarifier with 6/8 mm MS plate
Carrying out work on clarifier pipeline 2
Dismantling damaged 8inch size MS pipeline from clarifier clear juice overflow tank to sombox
Carrying out work on clarifier pipeline 3
Installing 6inch size MS pipeline from clarifier compartments no 2 and 3 to mud tank and providing satisfactory trial
Carrying out work on clarifier pipeline 4
Opening 6inch size valve and installing at designated location
Carrying out work on clarifier pipeline 5
Fabricating 6inch size nipple and installing at designated location
Carrying out work on clarifier pipeline 6
Fabricating 6inch size flange by cutting plate and dismantling to fit
Carrying out work on clarifier pipeline 7
Dismantling 4inch size air pipeline above door including nipple band flange and putting scrap in scrap yard
Carrying out work related to pipeline on big vacuum filter 1
Installing 4inch size air pipeline above door and providing satisfactory trial
Carrying out work related to pipeline on big vacuum filter 2
Dismantling 6inch size MS pipeline of big vacuum filter mud tank overflow line and putting scrap in scrap yard
Carrying out work related to pipeline on big vacuum filter 3
Fitting and trial of 6inch size MS pipeline overflow line of big vacuum filter mud tank at position
Carrying out work related to pipeline on big vacuum filter 4
Fabricating 6inch size band
Carrying out work related to pipeline on big vacuum filter 5
Fabricating 8inch size band
Carrying out work related to pipeline on big vacuum filter 6
Dismantling 8inch size pipeline from big vacuum filter pump to condenser and putting scrap in scrap yard
Fitting and trial of 8inch size pipeline from big vacuum filter pump to condenser at position
Fitting and trial of 8inch size pipeline from big vacuum filter pump to condenser at position
Dismantling 4inch MS pipeline from filter juice header to vibro screen
Dismantling 4inch MS pipeline from filter juice header to vibro screen
Fitting and trial of 4inch MS pipeline from filter juice header to vibro screen at position
Fitting and trial of 4inch MS pipeline from filter juice header to vibro screen at position
Making 4inch size nipple
Making 4inch size nipple
Opening 4inch size valve
Opening 4inch size valve
Installing 4inch size valve at the specified location
Installing 4inch size valve at the specified location
Carrying out work related to small vacuum filter pipelines etc 1
Cutting 4inch size flange from plate making it and fitting after drilling
Carrying out work related to small vacuum filter pipelines etc 2
Dismantling 3inch size pipeline
Carrying out work related to small vacuum filter pipelines etc 3
Installing and fitting 3inch size line at position and giving satisfactory trial
Carrying out work related to small vacuum filter pipelines etc 4
Making and installing 3inch size T
Carrying out work related to small vacuum filter pipelines etc 5
Making and installing 3inch size nipple
Carrying out work related to small vacuum filter pipelines etc 6
Cutting 3inch size flange from plate making it and installing
Carrying out work related to small vacuum filter pipelines etc 7
Making and installing 3inch size band
Carrying out work related to small vacuum filter pipelines etc 8
Dismantling 8inch size clear juice overflow pipeline
Carrying out work related to small vacuum filter pipelines etc 9
Installing and fitting 8inch size clear juice overflow pipeline at position and giving satisfactory trial
Carrying out work related to pipeline from juice sulfiter tank to juice tank 1
Making and installing 3inch size band
Carrying out work related to pipeline from juice sulfiter tank to juice tank 2
Dismantling 6inch size pipeline
Carrying out work related to pipeline from juice sulfiter tank to juice tank 3
Installing and fitting 6inch size pipeline at position and giving satisfactory trial
Carrying out work related to pipeline from juice sulfiter tank to juice tank 4
Making and installing 6inch size band/elbow at specified location
Carrying out work related to pipeline from juice sulfiter tank to juice tank 5
Making and installing 6inch size T
Carrying out work related to pipeline from juice sulfiter tank to juice tank 6
Dismantling 4inch size pipeline
Carrying out work related to pipeline from juice sulfiter tank to juice tank 7
Installing and fitting 4inch size pipeline at position and giving satisfactory trial
Carrying out work related to pipeline from juice sulfiter tank to juice tank 8
Making and installing 4inch size band
Carrying out work related to pipeline from juice tank to juice sulfiter
Making and installing 4inch size T
Carrying out work related to pipeline from juice tank to juice sulfiter
Dismantling 10inch size pipeline
Carrying out work related to pipeline from juice tank to juice sulfiter
Installing fitting and trial of 10inch size pipeline at position
Carrying out work related to pipeline from juice tank to juice sulfiter
Making and installing 10inch size T
Carrying out work related to pipeline from juice tank to juice sulfiter
Making and installing 10inch size dummy/flange
Carrying out work related to pipeline from juice tank to juice sulfiter
Dismantling 6inch pipeline
Carrying out work related to pipeline from juice tank to juice sulfiter
Installing fitting and trial of 6inch size pipeline at position
Carrying out work related to pipeline from juice tank to juice sulfiter
Making and fitting 6inch size flange
Carrying out work related to pipeline from juice tank to juice sulfiter
Opening and binding 6inch size valve
Carrying out work related to pipeline from juice tank to juice sulfiter
Dismantling 4inch size pipeline
Carrying out work related to pipeline from juice tank to juice sulfiter
Installing fitting and trial of 4inch size pipeline at position
Carrying out work related to pipeline from juice tank to juice sulfiter
Making and installing 8inch and 6inch size cross
Carrying out work related to pipeline from juice tank to juice sulfiter
Dismantling 4inch size ammonia pipeline of semichemiser quad
Carrying out work related to pipeline from juice tank to juice sulfiter
Installing 4inch size ammonia pipeline of semichemiser quad at position
Carrying out work related to pipeline from juice tank to juice sulfiter
Making 4inch size band
Carrying out work related to pipeline from juice tank to juice sulfiter
Making 4inch size T
Carrying out work related to pipeline from juice tank to juice sulfiter
Making 4inch size flange
Carrying out work related to pipeline from juice tank to juice sulfiter
Dismantling 2inch size pipeline
Carrying out work related to pipeline from juice tank to juice sulfiter
Fixing 2inch size pipeline in position
Carrying out work related to pipeline from juice tank to juice sulfiter
Fabricating and installing 2inch size flange
Carrying out work related to pipeline from juice tank to juice sulfiter
Dismantling new Quad No 2 vapor pipe 24inch size vapor pipeline fabricating it by bending with 10 mm thick plate and installing
Carrying out work related to pipeline from juice tank to juice sulfiter
Fabricating and installing 24inch size bends
Carrying out work related to pipeline from juice tank to juice sulfiter
Fabricating and installing 24inch size tees
Carrying out work related to pipeline from juice tank to juice sulfiter
Fabricating and installing 24inch size flange/dummy
Carrying out work related to pipeline from juice tank to juice sulfiter
Dismantling 24inch size pipeline
Carrying out work related to pipeline from juice tank to juice sulfiter
Fitting 24inch size pipeline in position
Carrying out work related to pipeline from juice tank to juice sulfiter
Fabricating and installing 24inch size flange
Carrying out work related to pipeline from juice tank to juice sulfiter
Cutting damaged 6inch syrup pump header fabricating new header and installing along with fitting all related nipples valves etc and conducting satisfactory trial
Carrying out work related to pipeline from juice tank to juice sulfiter
Dismantling bent incoming and outgoing wax and heater cell and partition plate between double beat valve of juice heater/ juice heater header fabricating new one using 12/10 mm plate as before installing and conducting satisfactory trial
Carrying out work related to pipeline from juice tank to juice sulfiter
Dismantling 6inch condensate header of juice heaters and replacing the weak part
Carrying out work related to pipeline from juice tank to juice sulfiter
Fitting 6inch size pipeline in position and conducting satisfactory trial
Carrying out work related to pipeline from juice tank to juice sulfiter
Fabricating and installing 6inch size flange
Carrying out work related to pipeline from juice tank to juice sulfiter
Fabricating and installing 6inch size nipple
Works related to juice sulfiter gas pipeline
Fabricating and installing 6inch size tees
Works related to juice sulfiter gas pipeline
Dismantling and fitting 6inch size pipeline in position and conducting satisfactory trial
Works related to juice sulfiter gas pipeline
Fabricating and installing 6inch size flange
| Item # | Title | Description | Quantity | Unit | Consignee | Delivery (Days) | Price Trends |
|---|---|---|---|---|---|---|---|
| 1 | Repairing the condensate tank pump delivery line of the pan 1 | Fabricate and install 6inch size nipple | 2 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 2 | Repairing the condensate tank pump delivery line of the pan 2 | Fabricate and install 6inch size flange | 4 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 3 | Repairing the condensate tank pump delivery line of the pan 3 | Dismantling 6inch size pipeline | 6 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 4 | Replacing damaged bypass line band flange of melter 1 | Installing 6inch size pipeline and giving satisfactory trial | 12 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 5 | Replacing damaged bypass line band flange of melter 2 | Fabricate and install 6inch size band | 4 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 6 | Replacing damaged bypass line band flange of melter 3 | Fabricate and install 6inch size flange | 5 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 7 | Replace damaged 100 pound 3inch size pipeline from Pan No 1 to Pan No 6 and give satisfactory trial | Replace damaged 100 pound 3inch size pipeline from Pan No 1 to Pan No 6 and give satisfactory trial | 30 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 8 | Replace the weak vapor pipe from Pan No 1 to 6 size dia 1 150 m length 30 m 1 | Dismantle the weak vapor pipe from Pan No 1 to 6 | 10 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 9 | Replace the weak vapor pipe from Pan No 1 to 6 size dia 1 150 m length 30 m 2 | Fabricate the weak vapor pipe from Pan No 1 to 6 | 10 | per ton | buyer10.cdgvvdup.up | 90 | |
| 10 | Replace main hole dia 600 mm of Pan No 3 Sevual with 10 mm thick plate | Replace main hole dia 600 mm of Pan No 3 Sevual with 10 mm thick plate | 1 | per ton | buyer10.cdgvvdup.up | 90 | |
| 11 | Replace damaged overflow pipeline of BH and CL molasses conditioner of 6inch size 1 | Replace damaged overflow pipeline of BH and CL molasses conditioner of 6inch size | 5 | per piece | buyer10.cdgvvdup.up | 90 | |
| 12 | Replace damaged overflow pipeline of BH and CL molasses conditioner of 6inch size 2 | Fabricate and install 6inch size band | 4 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 13 | Replace corroded nipples pipes flanges of 6inch size header on Pan No 5 and 6 install related nipples valves etc and give satisfactory trial | Replace corroded nipples pipes flanges of 6inch size header on Pan No 5 and 6 install related nipples valves etc and give satisfactory trial | 2 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 14 | Replace damaged ammonia pipeline flange nipple in Pan No 4 and 6 1 | Replace 2inch size pipeline | 30 | per piece | buyer10.cdgvvdup.up | 90 | |
| 15 | Replace damaged ammonia pipeline flange nipple in Pan No 4 and 6 2 | Fabricate and install 2inch size flange | 4 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 16 | Replace damaged ammonia pipeline flange nipple in Pan No 4 and 6 3 | Fabricate and install 2inch size nipple | 4 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 17 | Replace damaged ammonia pipeline flange nipple in Pan No 4 and 6 4 | Fabricate and install 3inch size flange | 6 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 18 | Replace damaged ammonia pipeline flange nipple in Pan No 4 and 6 5 | Fabricate and install 3inch size valve | 2 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 19 | Cut and remove damaged wash-out line installed on the pan and rebuild with supplied pipe and install it 1 | Replace and install 6inch size pipeline | 18 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 20 | Cut and remove damaged wash-out line installed on the pan and rebuild with supplied pipe and install it 2 | Fabricate and install 6inch size flange | 4 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 21 | Replace damaged washing pipeline nipple flange band on Pan No 6 1 | Replace 6inch size pipeline of the above | 6 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 22 | Replace damaged washing pipeline nipple flange band on Pan No 6 2 | Fabricate and install 6inch size flange | 6 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 23 | Replace damaged washing pipeline nipple flange band on Pan No 6 3 | Fabricate and install 6inch size nipple | 4 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 24 | Replace damaged washing pipeline nipple flange band on Pan No 6 4 | Fabricate and install 6inch size band | 4 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 25 | Install valve in steam line at Pan No 2 550 mm 1 | Install valve in steam line at Pan No 2 550 mm | 1 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 26 | Install valve in steam line at Pan No 2 550 mm 2 | Install flange in steam line at Pan No 2 550 mm | 4 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 27 | Install valve in steam line at Pan No 2 550 mm 3 | Install nipple in steam line at Pan No 2 550 mm | 1 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 28 | Install valve in steam line at Pan No 2 550 mm 4 | Fabricate and install catcher element size 75 X 75 X 8 angle on Pan No 4 and 5 | 2 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 29 | Replace nipple and band of A heavy tank 2 | Replace nipples of the above tank | 2 | per piece | buyer10.cdgvvdup.up | 90 | |
| 30 | Replace nipple and band of A heavy tank 3 | Replace bands of the above tank | 2 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 31 | Replace nipple and band of A heavy tank 4 | Replace partition of syrup tank with 10/12 mm thick plate | 10 | kg m | buyer10.cdgvvdup.up | 90 | |
| 32 | Remove clean and reinstall 4inch size syrup line on pan | Remove clean and reinstall 4inch size syrup line on pan | 120 | per m | buyer10.cdgvvdup.up | 90 | |
| 33 | Cut and remove syrup header and fabricate and install new header | Cut and remove syrup header and fabricate and install new header | 2 | per piece | buyer10.cdgvvdup.up | 90 | |
| 34 | Replacing the 6inch size glycol washing line fitted on Pan No 1 | Replacing the 6inch size glycol washing line fitted on Pan No 1 | 10 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 35 | Replacing nipples of different lines of Pan No 6 1 | Replacing nipples of 2inch size line mentioned above | 2 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 36 | Replacing nipples of different lines of Pan No 6 2 | Replacing nipples of 4inch size line mentioned above | 2 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 37 | Replacing nipples of different lines of Pan No 6 3 | Replacing nipples of 6inch size line mentioned above | 2 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 38 | Replacing nipples of different lines of Pan No 6 4 | Replacing nipples of 8inch size line mentioned above | 2 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 39 | Replacing 10inch size nipples of cut off line of Pan No 6 1 | Replacing 10inch size nipples of cut off line of Pan No 6 | 2 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 40 | Replacing 10inch size nipples of cut off line of Pan No 6 2 | Replacing 10inch size pipe line | 12 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 41 | Replacing 10inch size nipples of cut off line of Pan No 6 3 | Making and fitting 10inch size flange | 4 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 42 | Replacing 10inch size nipples of cut off line of Pan No 6 4 | Making and fitting 10inch size band | 2 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 43 | Replacing corroded hot water pipeline nipples flanges valves in Pan No 4 1 | Making and fitting 8inch size band | 2 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 44 | Replacing corroded hot water pipeline nipples flanges valves in Pan No 4 2 | Replacing 4inch size pipe line | 10 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 45 | Replacing corroded hot water pipeline nipples flanges valves in Pan No 4 3 | Making and fitting 4inch size flange | 4 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 46 | Replacing corroded hot water pipeline nipples flanges valves in Pan No 4 4 | Making and fitting 4inch size valve | 2 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 47 | Fabricating M S bed for syrup pump and motor fitting and alignment followed by satisfactory trial | Fabricating M S bed for syrup pump and motor fitting and alignment followed by satisfactory trial | 2 | lamsam | buyer10.cdgvvdup.up | 90 | |
| 48 | Dismantling weak condensate bottle of old set | Dismantling weak condensate bottle of old set vertical line juice heater and quad body No 4 disposing to scrap yard fabricating all connections using 8/10 mm plates and giving satisfactory vacuum trial | 2 | per piece | buyer10.cdgvvdup.up | 90 | |
| 49 | Replacing weak pipeline flange valve and band of old set vertical juice heater 1 | Replacing 2inch size pipeline | 15 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 50 | Replacing weak pipeline flange valve and band of old set vertical juice heater 2 | Replacing 6inch size pipeline | 15 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 51 | Replacing weak pipeline flange valve and band of old set vertical juice heater 3 | Making and fitting 2inch size flange | 4 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 52 | Replacing weak pipeline flange valve and band of old set vertical juice heater 4 | Making and fitting 6inch size flange | 4 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 53 | Replacing weak pipeline flange valve and band of old set vertical juice heater 5 | Making and fitting 6inch size band | 2 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 54 | Replacing weak pipeline of old Quad set No 4 1 | Making and fitting 6inch size valve | 2 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 55 | Replacing weak pipeline of old Quad set No 4 2 | Replacing 2inch size pipeline | 14 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 56 | Replacing weak pipeline of old Quad set No 4 3 | Replacing 6inch size pipeline | 18 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 57 | Replacing weak pipeline of old Quad set No 4 4 | Making and fitting 6inch size band | 2 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 58 | Replacing weak pipeline of old Quad set No 4 5 | Making and fitting 6inch size flange | 4 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 59 | Dismantling damaged mesh of section pipe located at Injection No 2 and 3 and making a new one from given M S plate and fitting it | Dismantling damaged mesh of section pipe located at Injection No 2 and 3 and making a new one from given M S plate and fitting it | 2 | per piece | buyer10.cdgvvdup.up | 90 | |
| 60 | Cutting and discarding old damaged reducer plate of section pipe located at Injection No 2 and 3 and remaking the same | Cutting and discarding old damaged reducer plate of section pipe located at Injection No 2 and 3 and remaking the same | 2 | per piece | buyer10.cdgvvdup.up | 90 | |
| 61 | Fitting water line from overhead to service tank 1 | Fitting mentioned line into service tank | 20 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 62 | Fitting water line from overhead to service tank 2 | Making and fitting 8inch size band | 2 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 63 | Details of work of Canti machine No 6 and 7 1 | Making and fitting 8inch size nipple | 1 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 64 | Details of work of Canti machine No 6 and 7 2 | Dismantling and fitting 6inch size pipeline | 18 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 65 | Details of work of Canti machine No 6 and 7 3 | Making and fitting 6inch size band | 6 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 66 | Details of work with new pipes from S Sugarbin 1 | Dismantling resistance box installed on spray making and fitting new one from given M M plate carrying out proper stay fitting and welding and conducting leak proof trial | 1 | per piece | buyer10.cdgvvdup.up | 90 | |
| 67 | Details of work with new pipes from S Sugarbin 2 | Dismantling and installing 8inch size pipeline | 6 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 68 | Details of work with new pipes from S Sugarbin 3 | Fabricating and installing 8inch size bands | 1 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 69 | Details of work for KCP No 1 and 2 and Canty Machine No 6 and 7 1 | Fabricating and installing 8inch size flanges | 4 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 70 | Details of work for KCP No 1 and 2 and Canty Machine No 6 and 7 2 | Dismantling and installing 12inch size pipeline | 8 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 71 | Details of work for KCP No 1 and 2 and Canty Machine No 6 and 7 3 | Fabricating and installing 12inch size bands | 2 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 72 | Work on hot water line of brown sugar magma 1 | Fabricating and installing 12inch size flanges | 4 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 73 | Work on hot water line of brown sugar magma 2 | Dismantling and installing 3inch size pipeline | 10 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 74 | Work on hot water line of brown sugar magma 3 | Manufacturing and installing 3inch size nipples | 2 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 75 | Work on hot water line of brown sugar magma 4 | Manufacturing and installing 3inch size bands | 1 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 76 | Cutting and removing damaged monitor casing and ribs | Cutting and removing damaged monitor casing and ribs inside Canty No 1 and 2 and KCP Machine 1 and 2 patching with 10/12 mm MS plate and giving satisfactory trial 1 | 2 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 77 | Cutting and removing damaged center shaft and arms inside KCP Machines No 1 and 2 bending and fitting new parts with 8 to 10 mm plate | Cutting and removing damaged center shaft and arms inside KCP Machines No 1 and 2 bending and fitting new parts with 8 to 10 mm plate 1 | 2 | lamsam | buyer10.cdgvvdup.up | 90 | |
| 78 | Dismantling damaged upper cover part of Canty Machine No 6 and 7 scrapping fabricating and fitting new cover with 12 mm plate and making all related connections | Dismantling damaged upper cover part of Canty Machine No 6 and 7 scrapping fabricating and fitting new cover with 12 mm plate and making all related connections | 2 | per unit | buyer10.cdgvvdup.up | 90 | |
| 79 | Dismantling damaged part of molasses weighing scale receiving tank and fabricating and fitting new part by bending 8 mm thick plate and depositing scrap in scrap yard | Dismantling damaged part of molasses weighing scale receiving tank and fabricating and fitting new part by bending 8 mm thick plate and depositing scrap in scrap yard | 1 | lamsam | buyer10.cdgvvdup.up | 90 | |
| 80 | Dismantling damaged plate of sugar discharge chute from sugar elevator to sugar grader and fabricating and fitting new plate of 6 mm thickness depositing scrap in scrap yard | Dismantling damaged plate of sugar discharge chute from sugar elevator to sugar grader and fabricating and fitting new plate of 6 mm thickness depositing scrap in scrap yard | 3 | per meter | buyer10.cdgvvdup.up | 90 | |
| 81 | Details of work from C magma to melter tank 1 | Modifying sugar chute of grader in dryer house and giving satisfactory trial | 4 | per unit | buyer10.cdgvvdup.up | 90 | |
| 82 | Details of work from C magma to melter tank 2 | Dismantling and installing 4inch size pipeline | 8 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 83 | Details of work from C magma to melter tank 3 | Fabricating and installing 4inch size flanges | 2 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 84 | Details of work from C magma to melter tank 4 | Manufacturing and installing 4inch size bands | 2 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 85 | Details of work from C magma to melter tank 5 | Manufacturing and installing 4inch size nipples | 3 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 86 | Repairing work details of final molasses tank 1 | Removing transit heater installed on C Centrifugal machine opening side plate for cleaning and hydraulic servicing reinstalling in place and making all connections | 2 | per unit | buyer10.cdgvvdup.up | 90 | |
| 87 | Repairing work details of final molasses tank 2 | Dismantling and installing 2inch size pipeline | 6 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 88 | Repairing work details of final molasses tank 3 | Fabricating and installing 2inch size flanges | 2 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 89 | Repairing work details of final molasses tank 4 | Manufacturing and installing 2inch size nipples | 4 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 90 | Repairing work details of final molasses tank 5 | Manufacturing and installing 2inch size valves | 1 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 91 | Details of work from melter to magma line 1 | Removing old taper of Sugar Hopper No 1 scrapping it fabricating new one from 3/5 mm MS plate installing and giving satisfactory trial | 1 | lamsam | buyer10.cdgvvdup.up | 90 | |
| 92 | Details of work from melter to magma line 2 | Dismantling and installing 6inch size pipeline | 16 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 93 | Details of work from melter to magma line 3 | Manufacturing and installing 6inch size bands | 3 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 94 | Details of work for A magma pump 1 | Manufacturing and installing 2inch size nipples | 1 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 95 | Details of work for A magma pump 2 | Manufacturing and installing 6inch size bands | 2 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 96 | Details of work for A magma pump 3 | Manufacturing and installing 6inch size flanges | 2 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 97 | Details of work for A magma pump 4 | Manufacturing and installing 5inch size flanges | 2 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 98 | Details of work for A magma pump 5 | Manufacturing and installing 5inch size valves | 2 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 99 | Details of work at ETP Effluent Treatment Plant1 | Removing damaged/weak top and bottom sugar discharge chute of Canty Machine No 4 including flange scrapping fabricating new parts with 6 mm MS plate as per suit sample preparing all connections like angle channel etc fitting on side and giving satisfactory trial | 1 | lamsam | buyer10.cdgvvdup.up | 90 | |
| 100 | Details of work at ETP Effluent Treatment Plant2 | Installing 2inch flow meter | 2 | per unit | buyer10.cdgvvdup.up | 90 | |
| 101 | Details of work at ETP Effluent Treatment Plant3 | Dismantling the damaged 6inch dia pipeline from primary clarifier to anoxic tank and putting it in scrap yard and installing a new pipeline | 100 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 102 | Details of work at ETP Effluent Treatment Plant4 | Dismantling and installing 4inch size pipeline | 7 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 103 | Details of work at ETP Effluent Treatment Plant5 | Installing 4inch size valve/NRV | 4 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 104 | Details of work at ETP Effluent Treatment Plant6 | Fabricating 4inch size band | 4 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 105 | Details of work at ETP Effluent Treatment Plant7 | Dismantling and installing 2inch size pipeline | 6 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 106 | Details of work at ETP Effluent Treatment Plant8 | Fabricating and installing 2inch size flange | 6 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 107 | Dismantling the damaged 8inch dia pipeline from aeration tank to secondary tank and putting it in scrap yard | Dismantling the damaged 8inch dia pipeline from aeration tank to secondary tank and putting it in scrap yard | 60 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 108 | Dismantling diffusers installed in aeration tank and putting them in scrap yard and replacing the throat part | Dismantling diffusers installed in aeration tank and putting them in scrap yard and replacing the throat part | 100 | per unit | buyer10.cdgvvdup.up | 90 | |
| 109 | In Sulfate Removal Plant reaction chamber dismantling corroded 6 mm partition plate putting it in scrap yard and fabricating with new 8 mm plate | In Sulfate Removal Plant reaction chamber dismantling corroded 6 mm partition plate putting it in scrap yard and fabricating with new 8 mm plate | 6 | per meter | buyer10.cdgvvdup.up | 90 | |
| 110 | Dismantling corroded 2inch size treated water outlet line of ETP and putting in scrap yard and installing new 3inch size line at the same location | Dismantling corroded 2inch size treated water outlet line of ETP and putting in scrap yard and installing new 3inch size line at the same location | 100 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 111 | Dismantling 800 mm dia exhaust pipe line below turbine with nipple band flange and putting in scrap yard | Dismantling 800 mm dia exhaust pipe line below turbine with nipple band flange and putting in scrap yard | 3 | per ton | buyer10.cdgvvdup.up | 90 | |
| 112 | Fabricating 800 mm dia exhaust pipeline below turbine from 12 mm plate by bending and installing at position and providing satisfactory trial | Fabricating 800 mm dia exhaust pipeline below turbine from 12 mm plate by bending and installing at position and providing satisfactory trial | 6 | per ton | buyer10.cdgvvdup.up | 90 | |
| 113 | Fabricating 800 mm dia exhaust pipeline below vapor cell 950 wag meter from 12 mm plate by bending and installing at position and providing satisfactory trial | Fabricating 800 mm dia exhaust pipeline below vapor cell 950 wag meter from 12 mm plate by bending and installing at position and providing satisfactory trial | 1 | per ton | buyer10.cdgvvdup.up | 90 | |
| 114 | Fabricating 800 mm dia exhaust pipeline below vapor cell 950 wag meter from 12 mm plate by bending into T shape and installing at position and providing satisfactory trial | Fabricating 800 mm dia exhaust pipeline below vapor cell 950 wag meter from 12 mm plate by bending into T shape and installing at position and providing satisfactory trial | 1 | running meter | buyer10.cdgvvdup.up | 90 | |
| 115 | Fabricating work | Fabricating 800 mm dia exhaust pipeline dummy/flange from 12 mm plate by bending and installing at position and providing satisfactory trial | 4 | per unit | buyer10.cdgvvdup.up | 90 | |
| 116 | Dismantling weak part of semichemiser 1000 wag meter | Dismantling weak part of semichemiser 1000 wag meter warm saser putting scrap in scrap yard fabricating from 12 mm thick plate by bending and installing with related connections and giving satisfactory trial Size dia 3 4 m | 1 | running meter | buyer10.cdgvvdup.up | 90 | |
| 117 | Dismantling weak parts of old quad body no 2 and 3 20inch vapor pipe putting scrap in scrap yard fabricating from 8 mm thick plate by bending and installing and providing satisfactory trial | Dismantling weak parts of old quad body no 2 and 3 20inch vapor pipe putting scrap in scrap yard fabricating from 8 mm thick plate by bending and installing and providing satisfactory trial | 16 | per meter | buyer10.cdgvvdup.up | 90 | |
| 118 | Dismantling weak parts of vapor pipe 32inch size of vapor cell 1000 wag meter putting scrap in scrap yard fabricating from 8 mm thick plate by bending and installing and providing satisfactory trial | Dismantling weak parts of vapor pipe 32inch size of vapor cell 1000 wag meter putting scrap in scrap yard fabricating from 8 mm thick plate by bending and installing and providing satisfactory trial | 8 | per meter | buyer10.cdgvvdup.up | 90 | |
| 119 | Dismantling weak part of 6inch size header of all juice heaters condensate and installing new one | Dismantling weak part of 6inch size header of all juice heaters condensate and installing new one | 22 | per meter | buyer10.cdgvvdup.up | 90 | |
| 120 | Removing all partition plates | Removing all partition plates of juice heater header by cutting straight and circular shapes cleaning tube plate completely and fabricating new circular and straight partition plates from 10/12 mm plate installing and preparing header with MS strips as before applying rubber strips and providing satisfactory trial | 3 | per unit | buyer10.cdgvvdup.up | 90 | |
| 121 | Cutting out quailons and all related angles | Cutting out quailons and all related angles fixed in clarifier compartments and refitting after completion of work and providing satisfactory trial | 8 | per unit | buyer10.cdgvvdup.up | 90 | |
| 122 | Carrying out work on clarifier pipeline 1 | Patching inside clarifier with 6/8 mm MS plate | 10 | per square meter | buyer10.cdgvvdup.up | 90 | |
| 123 | Carrying out work on clarifier pipeline 2 | Dismantling damaged 8inch size MS pipeline from clarifier clear juice overflow tank to sombox | 18 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 124 | Carrying out work on clarifier pipeline 3 | Installing 6inch size MS pipeline from clarifier compartments no 2 and 3 to mud tank and providing satisfactory trial | 18 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 125 | Carrying out work on clarifier pipeline 4 | Opening 6inch size valve and installing at designated location | 2 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 126 | Carrying out work on clarifier pipeline 5 | Fabricating 6inch size nipple and installing at designated location | 2 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 127 | Carrying out work on clarifier pipeline 6 | Fabricating 6inch size flange by cutting plate and dismantling to fit | 3 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 128 | Carrying out work on clarifier pipeline 7 | Dismantling 4inch size air pipeline above door including nipple band flange and putting scrap in scrap yard | 18 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 129 | Carrying out work related to pipeline on big vacuum filter 1 | Installing 4inch size air pipeline above door and providing satisfactory trial | 18 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 130 | Carrying out work related to pipeline on big vacuum filter 2 | Dismantling 6inch size MS pipeline of big vacuum filter mud tank overflow line and putting scrap in scrap yard | 24 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 131 | Carrying out work related to pipeline on big vacuum filter 3 | Fitting and trial of 6inch size MS pipeline overflow line of big vacuum filter mud tank at position | 24 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 132 | Carrying out work related to pipeline on big vacuum filter 4 | Fabricating 6inch size band | 3 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 133 | Carrying out work related to pipeline on big vacuum filter 5 | Fabricating 8inch size band | 3 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 134 | Carrying out work related to pipeline on big vacuum filter 6 | Dismantling 8inch size pipeline from big vacuum filter pump to condenser and putting scrap in scrap yard | 24 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 135 | Fitting and trial of 8inch size pipeline from big vacuum filter pump to condenser at position | Fitting and trial of 8inch size pipeline from big vacuum filter pump to condenser at position | 24 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 136 | Dismantling 4inch MS pipeline from filter juice header to vibro screen | Dismantling 4inch MS pipeline from filter juice header to vibro screen | 24 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 137 | Fitting and trial of 4inch MS pipeline from filter juice header to vibro screen at position | Fitting and trial of 4inch MS pipeline from filter juice header to vibro screen at position | 24 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 138 | Making 4inch size nipple | Making 4inch size nipple | 2 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 139 | Opening 4inch size valve | Opening 4inch size valve | 1 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 140 | Installing 4inch size valve at the specified location | Installing 4inch size valve at the specified location | 1 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 141 | Carrying out work related to small vacuum filter pipelines etc 1 | Cutting 4inch size flange from plate making it and fitting after drilling | 2 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 142 | Carrying out work related to small vacuum filter pipelines etc 2 | Dismantling 3inch size pipeline | 36 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 143 | Carrying out work related to small vacuum filter pipelines etc 3 | Installing and fitting 3inch size line at position and giving satisfactory trial | 36 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 144 | Carrying out work related to small vacuum filter pipelines etc 4 | Making and installing 3inch size T | 10 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 145 | Carrying out work related to small vacuum filter pipelines etc 5 | Making and installing 3inch size nipple | 4 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 146 | Carrying out work related to small vacuum filter pipelines etc 6 | Cutting 3inch size flange from plate making it and installing | 4 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 147 | Carrying out work related to small vacuum filter pipelines etc 7 | Making and installing 3inch size band | 6 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 148 | Carrying out work related to small vacuum filter pipelines etc 8 | Dismantling 8inch size clear juice overflow pipeline | 18 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 149 | Carrying out work related to small vacuum filter pipelines etc 9 | Installing and fitting 8inch size clear juice overflow pipeline at position and giving satisfactory trial | 18 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 150 | Carrying out work related to pipeline from juice sulfiter tank to juice tank 1 | Making and installing 3inch size band | 3 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 151 | Carrying out work related to pipeline from juice sulfiter tank to juice tank 2 | Dismantling 6inch size pipeline | 18 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 152 | Carrying out work related to pipeline from juice sulfiter tank to juice tank 3 | Installing and fitting 6inch size pipeline at position and giving satisfactory trial | 18 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 153 | Carrying out work related to pipeline from juice sulfiter tank to juice tank 4 | Making and installing 6inch size band/elbow at specified location | 2 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 154 | Carrying out work related to pipeline from juice sulfiter tank to juice tank 5 | Making and installing 6inch size T | 2 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 155 | Carrying out work related to pipeline from juice sulfiter tank to juice tank 6 | Dismantling 4inch size pipeline | 18 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 156 | Carrying out work related to pipeline from juice sulfiter tank to juice tank 7 | Installing and fitting 4inch size pipeline at position and giving satisfactory trial | 18 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 157 | Carrying out work related to pipeline from juice sulfiter tank to juice tank 8 | Making and installing 4inch size band | 4 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 158 | Carrying out work related to pipeline from juice tank to juice sulfiter | Making and installing 4inch size T | 4 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 159 | Carrying out work related to pipeline from juice tank to juice sulfiter | Dismantling 10inch size pipeline | 6 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 160 | Carrying out work related to pipeline from juice tank to juice sulfiter | Installing fitting and trial of 10inch size pipeline at position | 6 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 161 | Carrying out work related to pipeline from juice tank to juice sulfiter | Making and installing 10inch size T | 3 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 162 | Carrying out work related to pipeline from juice tank to juice sulfiter | Making and installing 10inch size dummy/flange | 4 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 163 | Carrying out work related to pipeline from juice tank to juice sulfiter | Dismantling 6inch pipeline | 18 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 164 | Carrying out work related to pipeline from juice tank to juice sulfiter | Installing fitting and trial of 6inch size pipeline at position | 18 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 165 | Carrying out work related to pipeline from juice tank to juice sulfiter | Making and fitting 6inch size flange | 2 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 166 | Carrying out work related to pipeline from juice tank to juice sulfiter | Opening and binding 6inch size valve | 1 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 167 | Carrying out work related to pipeline from juice tank to juice sulfiter | Dismantling 4inch size pipeline | 6 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 168 | Carrying out work related to pipeline from juice tank to juice sulfiter | Installing fitting and trial of 4inch size pipeline at position | 6 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 169 | Carrying out work related to pipeline from juice tank to juice sulfiter | Making and installing 8inch and 6inch size cross | 1 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 170 | Carrying out work related to pipeline from juice tank to juice sulfiter | Dismantling 4inch size ammonia pipeline of semichemiser quad | 12 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 171 | Carrying out work related to pipeline from juice tank to juice sulfiter | Installing 4inch size ammonia pipeline of semichemiser quad at position | 12 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 172 | Carrying out work related to pipeline from juice tank to juice sulfiter | Making 4inch size band | 1 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 173 | Carrying out work related to pipeline from juice tank to juice sulfiter | Making 4inch size T | 2 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 174 | Carrying out work related to pipeline from juice tank to juice sulfiter | Making 4inch size flange | 2 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 175 | Carrying out work related to pipeline from juice tank to juice sulfiter | Dismantling 2inch size pipeline | 2 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 176 | Carrying out work related to pipeline from juice tank to juice sulfiter | Fixing 2inch size pipeline in position | 2 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 177 | Carrying out work related to pipeline from juice tank to juice sulfiter | Fabricating and installing 2inch size flange | 1 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 178 | Carrying out work related to pipeline from juice tank to juice sulfiter | Dismantling new Quad No 2 vapor pipe 24inch size vapor pipeline fabricating it by bending with 10 mm thick plate and installing | 10 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 179 | Carrying out work related to pipeline from juice tank to juice sulfiter | Fabricating and installing 24inch size bends | 1 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 180 | Carrying out work related to pipeline from juice tank to juice sulfiter | Fabricating and installing 24inch size tees | 1 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 181 | Carrying out work related to pipeline from juice tank to juice sulfiter | Fabricating and installing 24inch size flange/dummy | 1 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 182 | Carrying out work related to pipeline from juice tank to juice sulfiter | Dismantling 24inch size pipeline | 10 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 183 | Carrying out work related to pipeline from juice tank to juice sulfiter | Fitting 24inch size pipeline in position | 10 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 184 | Carrying out work related to pipeline from juice tank to juice sulfiter | Fabricating and installing 24inch size flange | 1 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 185 | Carrying out work related to pipeline from juice tank to juice sulfiter | Cutting damaged 6inch syrup pump header fabricating new header and installing along with fitting all related nipples valves etc and conducting satisfactory trial | 2 | per header | buyer10.cdgvvdup.up | 90 | |
| 186 | Carrying out work related to pipeline from juice tank to juice sulfiter | Dismantling bent incoming and outgoing wax and heater cell and partition plate between double beat valve of juice heater/ juice heater header fabricating new one using 12/10 mm plate as before installing and conducting satisfactory trial | 6 | per box | buyer10.cdgvvdup.up | 90 | |
| 187 | Carrying out work related to pipeline from juice tank to juice sulfiter | Dismantling 6inch condensate header of juice heaters and replacing the weak part | 22 | per meter | buyer10.cdgvvdup.up | 90 | |
| 188 | Carrying out work related to pipeline from juice tank to juice sulfiter | Fitting 6inch size pipeline in position and conducting satisfactory trial | 22 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 189 | Carrying out work related to pipeline from juice tank to juice sulfiter | Fabricating and installing 6inch size flange | 20 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 190 | Carrying out work related to pipeline from juice tank to juice sulfiter | Fabricating and installing 6inch size nipple | 2 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 191 | Works related to juice sulfiter gas pipeline | Fabricating and installing 6inch size tees | 2 | pcdn | buyer10.cdgvvdup.up | 90 | |
| 192 | Works related to juice sulfiter gas pipeline | Dismantling and fitting 6inch size pipeline in position and conducting satisfactory trial | 6 | pcdm | buyer10.cdgvvdup.up | 90 | |
| 193 | Works related to juice sulfiter gas pipeline | Fabricating and installing 6inch size flange | 18 | pcdn | buyer10.cdgvvdup.up | 90 |
Discover companies most likely to bid on this tender
GST registration certificate
Permanent Account Number (PAN) card
Audited financial statements for the last three financial years or CA certificate indicating turnover
Past experience proofs: contract copies with invoices and client execution certificates or equivalent
Technical compliance certificates (as applicable)
OEM authorizations or supplier certifications (if required by the bid)
Any other documents listed in the Bid Document/ATC or Corrigendum
Extended Deadline
21-Jul-2026, 3:00 pm
Opening Date
21-Jul-2026, 3:30 pm
Extended Deadline
17-Jul-2026, 3:00 pm
Opening Date
17-Jul-2026, 3:30 pm
Key insights about UTTAR PRADESH tender market
Bidders should review the ATC and corrigenda, prepare turnover documents (audited statements/CA certificate), compile past experience proofs (contract copies or client certificates), and upload GST, PAN, and required certificates. Ensure compliance with the 25% quantity option and minimum 30-day delivery timeline.
Required documents include GST certificate, PAN, audited turnover statements for the last three years or CA certificate, past project experience proofs, technical compliance certificates, OEM authorizations if applicable, and any certificates specified in the Bid Document/ATC.
The tender has an estimated value of ₹450,000 with 193 BOQ items reported as N/A; bidders should confirm item specifics from the official bid document and be prepared for quantity variations up to 25%.
Delivery begins from the last date of the original order; additional time is (increased quantity / original quantity) × original delivery period, with a minimum of 30 days. The purchaser may extend time to cover up to the original delivery period.
Eligibility requires meeting turnover criteria for the last three years, providing past-experience proofs (contracts or client certificates), and uploading required certificates per ATC and corrigenda; non-compliance risks bid rejection.
The tender data does not specify standards; bidders must rely on the Bid Document/ATC for exact certification requirements and any OEM authorizations or quality standards referenced there.
EMD details are not provided in the data; bidders must verify the exact EMD amount, payment method, and submission procedure in the Bid Document and ensure readiness before the bid deadline.
Acceptable proofs include contract copies with invoices and bidder self-certification, execution certificates from clients, or other supporting documents like third-party inspection notes, as permitted in the ATC.
Directorate of Local Bodies UP
📍 KANPUR NAGAR, UTTAR PRADESH
Bharat Heavy Electricals Limited (bhel)
Bharat Coking Coal Limited
📍 DHANBAD, JHARKHAND
All India Institute of Medical Sciences-Rishikesh
📍 DEHRADUN, UTTARAKHAND
KOLKATA MUNICIPAL CORPORATION
📍 KOLKATA, WEST BENGAL
Sign up now to access all documents
Main Document
BOQ
BOQ
GEM_GENERAL_TERMS_AND_CONDITIONS