Government Tender Published for Rack steel 6 tier 1905 x 915 x 305mm,Locker Steel,Receptable PVC,Table office offr steel,Table cent in CHANDIGARH, CHANDIGARH

All as shown on drg The overall size shall be 915 mm long 610mm wide and 1905mm high Four vertical angle iron of 40mm x 40mm x 4mm shall be provided at four corners Top bottom sides back shelves shall be of 1mm thick mild steel sheet The bottom sheet shall be at 100mm from bottom Five shelves equally spaced to make six equal compartments shall be provided of 1mm thick mild steel sheet Four 75mm x 75mm x 3mm flat iron cut to shape to angular brackets shall be ovided on front side as shown on drawing All steel surfaces exposed to view when placed in position shall be given two coats of enamel paint colour approved by GE over a coat of primer with spray machine after preparation of steel surfaces All MS members shall Painted colour approved by GE with spray machine

Receptacle shall be made of thick polymer palstic of capacity 20 ltr with the pendulam type lid and steel handle on both side all as shown on drawing The colour shall only be red green or blue The contractor may also provide the readymade receptacle PVC of make Milton Cello Brite with the same specifications

All as shown on drawing Overall size shall be 900mm long 450mm wide and 400mm high All wood shall be of first class hard wood teak MP Legs shall be made of 60mm x 30mm in section teak wood 356mm high Hard rubber PVC shoes shall be fixed to the bottom of legs with steel screws Pre laminated particle board teak faced exterior grade of the table 5mmx5mm in section groove shall be provided in the visible portion of top of legs Legs shall be joined togeter in short and long side with top rails of 20mm thick and 50mm high Top of table shall be fixed of legs and top rails with 50mm long screws four in numbers from below the each top long rails 50mm wide and 20mm thick stiffener 430mm long shall be fixed in the center of top rails joining top long rails with dove tail joints. Side rails 50mm x 20mm in section at 100mm from bottom of legs shall be provided joining legs in short sides 4mm thick teak wood edging shall be provided at the alround edges of top of table Irrespective of what is shown on drawing a bottom tier shall be fixed on the top of bottom side rail with 50mm long screw The bottom tier shall be of 18mm thick pre laminated particle board teak faced exterior grade of the table 4mm thick teak wood edging shall be provided alround the eges of bottom tier All wood surfaces exposed to view when placed in position shall be melamine polished with high gloss finish lacquer finish

i All wood work shall be of 1st class hard wood Teak ii Seat shall be woven with cane plastic 2 mm wide 0 point4 mm thick half found white or cream in colour Border shall be 3 mm wide 0 point 5 mm thick flat plastic cane Weaving shall be done as per Godrej Pattern iii All exposed surfaces of timber shall be melamine polished twice with high gloss finish after preparation of surfaces iv Hard rubber PVC shoes shall be provided to the bottom of each leg v All joints fixing shall be done in accordance with standard workmanship and specifications vi Rest all as per trade practice and as shown in drawing

All as shown on drawing All wood shall be seasoned first class hardwood teak MP Leg of chair shall be of 55mm x 25mm in section at place under side armrest tapering to the bottom of legs of 25mm x 25mm in section Front legs shall be jointed by 50mm x 25mm in section rails provided below seat frame for the support of frame Rear legs shall be 55mm x 25mm in section below arm rest and 25mm x 25mm in section of bottom of legs Rear legs shall be joint together by rails of 50mm x 25mm in section provided at the bottom of seat frame Seat frame shall have the rear horizontal made out of section 70mm x 40mm joining the sides of frame which shall be 70mm x 40mm at the back and the seat frame shall be of size 510mm long in front 480mm long at rear and 575mm deep The top horizontal rail of back rest shall be made out of 55mm 40mm and shall be 50mm x 20mm The bottom horizontal frame of back rest shall be of shape as shown on drawing The arm rests made out 65mm x 25mm in section and 610mm long shall be provide in shape as shown on drawing Seat and back shall be woven with the plastic cane in Godrej pattern with 20 mm wide and 0 point 4mm thick half round gola type white plastic cane with 3 point 0mm wide plastic cane border of approved make Hard rubber rings PVC toes shall be provided to bottom of all legs with the screws All wood surface exposed to view when placed in position shall be melamine polished with the high gloss finish