Contract Bidding Open For TITLE1,TITLE2,TITLE3,TITLE4,TITLE5,TITLE6,TITLE7,TITLE8,TITLE9,TITLE10,TITLE11,TITLE12,TITLE13,TITL in EAST SINGHBHUM, JHARKHAND

Clearing jungle including uprooting of rank vegetation grass brush wood trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.

Diluting and injecting chemical emulsion for POST CONSTRUCTIONAL anti termite treatment excluding the cost of chemical emulsion Along external wall where the apron is not provided using chemical emulsion at the rate 7.5 litres or sqm of the vertical surface of the substructure to a depth of 300mm including excavation channel along the wall and rodding etc. complete isto With Chlorpyriphos or Lindane E.C. 20 Percent with 1 Percent concentration

Filling available excavated earth excluding rock in trenches plinth sides of foundations etc. in layers not exceeding 20cm in depth consolidating each deposited layer by ramming and watering lead up to 50 m and lift upto 1.5 m

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering All work up to plinth level 1 isto 3 isto 6 1 Cement 3 coarse sand zone III 6 graded stone aggregate 20 mm nominal size

Reinforced cement concrete work in walls any thickness including attached pilasters buttresses plinth roof and string courses fillets columns pillars piers abutments posts and struts etc. above plinth level up to floor five level excluding cost of centering shuttering finishing and reinforcement 1 isto 1.5 isto 3 1 cement 1.5 coarse sand zone III 3 graded stone aggregate 20 mm nominal size

Brick work with common burnt clay F.P.S. non modular bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in Cement mortar 1 isto 6 1 cement 6 coarse sand

Centering and shuttering including strutting propping etc. and removal of form for Foundations footings bases of columns etc. for mass concrete

Steel reinforcement for R.C.C. work including straightening cutting bending placing in position and binding all complete upto plinth level Thermo Mechanically Treated bars of grade Fe 500D or more Make SAIL or TATA or JINDAL

12 mm cement plaster of mix 1 isto 6 1 cement isto 6 fine sand Rates for external plastic are for height upto 10m from ground level in less otherwise stated Cement Make Nuvoco Lafarge or UltraTech or ACC or as per direction of EIC

Neat cement punning.

White washing with lime to give an even shade New work three or more coats mix with fevicol DDL and Robin Blue or as per direction of EIC

Making plinth protection 50mm thick of cement concrete 1 isto 3 isto 6 1 cement 3 coarse sand zone III 6 graded stone aggregate 20 mm nominal size over 75mm thick bed of dry brick ballast 40 mm nominal size well rammed and consolidated and grouted with fine sand including necessary excavation levelling and dressing and finishing the top smooth

Providing and fixing ISI marked flush door shutters conforming to IS isto 2202 Part I decorative type core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws

25 mm thick PVC flush door shutters made out of a one piece Multi chamber extruded PVC section of the size of 762 mm into 25 mm or less as per requirement with an average wall thickness of 1 mm plus or minus 0.3 mm . PVC foam end cap of size 23x10 mm are provided on both vertical edges to ensure the overall thickness of 25 mm. M.S. tube having dimensions 19 mm into 19 mm and 1.0 mm plus or minus 0.1 mm is inserted along the hinge side of the door. Core of the door shutter should be filled with High Density Polyurethane foam. The Top and Bottom edges of the shutter are covered with an end cap of the size 25 mm into 11 mm. Door shutter shall be reinforced with special polymeric reinforcements as per manufacturer specification and direction of Engineer in charge to take up necessary hardware and fixtures. Stickers indicating the locations of hardware will be pasted at appropriate places

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS 15622 thickness to be specified by the manufacturer of approved make Somany or Kajaria or Nitco in all colours shades except burgundy bottle green black of any size as approved by Engineer in Charge in skirting risers of steps and dados over 12 mm thick bed of cement mortar 1 isto 3 1 cement 3 coarse sand and jointing with grey cement slurry at the rate 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. Make isto Somany or Kajaria or Nitco or Asian or as per direction of EIC

Providing and fixing water closet squatting pan Indian type W.C.pan with 100 mm sand cast Iron P or S trap 10 litre low level white P.V.C. flushing cistern including flush pipe with manually controlled device handle lever conforming to IS 7231 with all fittings and fixtures complete including cutting and making good the walls and floors wherever required White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests Preferable Make Hindware or Parrywair or Hindustan or Cera or direction of EIC

Providing and fixing wash basin with C.I. brackets 15 mm C.P. brass pillar taps 32 mm C.P. brass waste of standard pattern including painting of fittings and brackets cutting and making good the walls wherever require isto White Vitreous China Wash basin size 630x450 mm with a single 15 mm C.P. brass pillar tap

Providing and fixing 600x450 mm beveled edge mirror of superior glass of approved quality complete with 6 mm thick hard board ground fixed to wooden cleats with C.P . brass screws and washers complete.

Providing and fixing brass stop cock of approved quality 15 mm nominal bore

Providing and fixing ISI marked oxidised M. S handles conforming to IS 4992 with necessary screws etc. complete 125 mm

Providing and fixing IS 12817 marked stainless steel butt hinges heavy weight with stainless steel screws etc. complete 100x60x2.50 mm

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. for External work b. 20 mm dia nominal bore Preferable Make TATA or Jindal or as per direction of EIC

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS 13592 Type A including jointing with seal ring conforming to IS 5382 leaving 10 mm gap for thermal expansion Single socketed pipes. 110 mm diameter

Providing and fixing gun metal gate valve with C.I. wheel of approved quality screwed end isto 50 mm nominal bore

Providing and fixing 100 mm sand cast Iron grating for gully trap

Constructing masonry Chamber 30x30x50 cm inside in brick work in cement mortar 1 isto 4 1 cement isto 4 coarse sand for stop cock with C. I. surface box 100x100 x75 mm inside with hinged cover fixed in cement concrete slab 1 isto 2 isto 4 mix 1 cement isto 2 coarse sand isto 4 graded stone aggregate 20 mm nominal size i or c necessary excavation foundation concrete 1 isto 5 isto 10 1 cement isto 5 fine sand isto 10 graded stone aggregate 40mm nominal size and inside plastering with cement mortar 1 isto 3 1 cement isto 3 coarse sand 12mm thick finished with a floating coat of neat cement complete as per standard design isto With common burnt clay F.P.S. non modular bricks of class designation 7.5

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter 1.8 m long complete as per standard design. With common burnt clay F.P.S. non modular bricks of class designation 7.5

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm plus 0.05 Percent total coated thickness Zinc coating 120 grams per sqm as per IS 277 in 240 mpa steel grade 5 to 7 microns epoxy primer on both side of the sheet and polyester top coat 15 to 18 microns using self drilling or self tapping screws complete Ridges plain 500 to 600mm

Providing and fixing of glass panes with putty and glazing clips in steel doors and windows all complete with 4mm thick glass panes etc. Complete.

Fixing of LED Tube light fittings including supply of all hardwares as required. LED fitting will be supplied by contractor. Make C.G. or Philips

Fixing of 48 sweep ceiling fan complete with down rod.Clamp canopy etc.Fan Hardwares required for fixing for i.e. nut bolts clamp screws etc wiil be supplied by contractor.

Wiring for light point fan point exhaust fan point with 1.5 sqmm FRLS PVC insulated copper conductor single core cable in consield with modular switch modular plate suitable GI box and earthing the point with 1.5 sqmm FRLs PVC insulated copper conductor cable as required.

Wiring for circuit or submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable in consield or recessed medium class PVC conduit in concield as required 2 X 6 sqmm plus 1 X 6 sqmm earth wire. All the three colours should be RED Blue and Green

Supply and installation of Three Phase Industrial Box With 32 Amp 4 Pole MCB And 5 Pin Top Plug. Make Neptune or Reputed make

Wiring for circuit or submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor single core cable in surface or recessed medium class PVC conduit in concield as required 4 X 10 sqmm + 1 X 10 sqmm earth wire.All the five colours should be RED Blue yellow black and Green

Supply and laying 25mm X 5 MM GI strip at 0.5 meter below ground or wall including connection with electrode with DB. Supply of all hardware are in scope of Contractor

Supply and fixing of 5 to 32 Amp rating 240 or 415 Volt MCB suitable as per load.

Laying of 1.1KV grade PVC Al.cable of size 2 or 3 or 3.5 or 4C 2.5 or 6 or 10 or 16 or 25 or 35 sq.mm in underground trench of 760mm deepX760mm wide in single tier formation including trench excavation and back filling with bricks 15brick or m and sand protection route marker. Road or concreete or bolder cutting and finishing the road to its original shape are in the scope of the contractor.

Supply and fixing of Bulk Head fitting on wall including supply of all necessaryu hardware for fixing of fitting on wall.